687703
1
Zoom out
Zoom in
Previous page
1/2
Next page
2
Less than 50cm
2. Name : Sensor Name
3. : Search this sensor. If searched, the sensor LED will flash five times.
4. Alarm On/Off :Alarm On will enable you to receive push message when
Door/Window sensor event is triggered.
5. : The camera will rotate to a preset position when “Alarm On” and
Door/Window sensor event is triggered. Through live view window to position
the camera and tap “Locate” to confirm.
1. No. : Sensor Number. Tap it to select other sensor. (No. 0,1,2.)
Sensor Setting
3
1
2
4
3
5
DWM_001
RF_Door/ Window Sensor
Installation Guide
Manuel de l'utilisateur
Guía de instalación
Installationsanleitung
Guida all'installazione
Step1: Battery On
2. Install two AAA batteries.
Step2: Sensor Pairing
1. Turn on camera and launch “iSmart-CAMAPP. Go to “Camera Setting
and tap ”IoT Sensor Setting.
2. Tap the then hold the pairing button for 3 seconds
within 5 seconds.
3. The sensor type will be displayed after paring completed.
4. Tap the “Door/Window Sensor” for detailed settings.
Note: If pairing successfully, the LED will light up for 3 seconds.
If failed, the LED will blink.
1. Remove the back cover.
Align with positive (+) and negative (-)
as indicated inside the battery
compartment.
1
Pairing Button.
2. LED Light.
3. Magnetic Reed Switch.
1.
Product Layout
1
Quick Setup
2
2
1
3
ENGLISH
FRANÇAIS
ESPAÑOL
Étape 1 : Installation des piles
1. Retirez le couvercle arrière.
2. Installez deux piles AAA.
Alignez avec le positif (+) et le négatif (-)
comme indiqué à l'intérieur du
compartiment des piles
Étape 2 : Appairage du capteur
1. Allumez la caméra et lancez l'application « iSmart-CAM ». Allez dans
« Paramétrage caméra » et appuyez sur « Paramétrage capteur IoT ».
2. Appuyez sur puis maintenez le bouton d'appairage enfoncé
pendant 3 secondes et moins de 5 secondes.
3. Le type de capteur s'affiche une fois l'appairage effectué.
4. Appuyez sur “Capteur Porte/Fenêtre” pour accéder aux paramètres détaillés.
Si l'appairage est réussi, la LED s'allume pendant 3 secondes.
S'il échoue, la LED clignote.
Remarque :
4
Bouton d'appairage.
2. Éclairage LED.
3. Interrupteur magnétique
à lames souples.
1.
Description du produit
1
Configuration rapide
2
5
Moins de 50 cm
(N° 0, 1, 2, ...)
2. Nom : Nom du capteur
3. : Rechercher ce capteur. S'il est trouvé, le capteur LED clignote cinq fois.
4. Alarme activée/désactivée : « Alarme activée » vous permet de recevoir un
message push quand l'événement capteur Porte/Fenêtre est déclenché.
5. : La caméra tourne jusqu'à une position présélectionnée quand
« Alarme activée » et l'événement capteur Porte/Fenêtre est déclenché.
Avec la fenêtre de visualisation en direct, positionnez la caméra et appuyez sur
« Localiser » pour confirmer.
1. Appuyez pour sélectionner un autre capteur. N° : Numéro du capteur.
Configuration du capteur
3
1
2
4
3
5
Positionnement
4
-
- Dimensions : 66 x 34 x 25 mm, Aimant : 58 x 13 x 15 mm
- Poids : 32,5 g
- Intervalle de détection du capteur magnétique activé : 10 mm
- Distance de fonctionnement RF : 30 mètres* (intérieur)
- Alimentation : 3 (AAAx2,Vpiles alcalines conseillées)
- Autonomie des piles : 1 an* (Déclenchement 20 fois par jour)
- Température de fonctionnement : 0 ~ 40 (32 ~ 104 )
*La distance de fonctionnement et l'autonomie des piles réelles peuvent
varier en fonction des modes d'utilisation et de l'environnement
de fonctionnement.
Cet appareil est adapté à une utilisation à l'intérieur uniquement.
Aucune résistance à l'eau.
Lorsque la batterie est faible, la LED clignote et l'appairage est impossible.
-
Modulation : GFSK
Principal:
Fréquence : 2,4 GHz
Spécifications
5
1 cm (maxi)
6
Paso 1: Colocar las pilas
1. Retire la tapa posterior.
2. Instale dos pilas de tipo AAA.
Realice la alineación con los polos
positivo (+) y negativo (-) según se indica
dentro del compartimento de la batería.
Paso 2: Asociar el sensor
1. Encienda la cámara e inicie la aplicación “iSmart-CAM. Vaya a
Configuración de la cámara” y pulse “Establecer el sensor IoT.
2. Pulse y, a continuación, mantenga pulsado el botón de
asociación durante 3 segundos antes de que transcurran 5 segundos.
3. El tipo de sensor se mostrará después de que la asociación se complete.
4. Pulse “Sensor de puertas y ventanas” para obtener una configuración detallada.
: Si la asociación se realiza correctamente, el LED se iluminará durante
3 segundos. En caso contrario, el LED parpadeará.
Nota
7
Botón Asociar.
2. Luz de LED.
3. Conmutador rojo magnético.
1.
Diseño del producto
1
Configuración rápida
2
Placement
4
- Modulation: GFSK
- Dimensions: Main: 66x34x25mm,
Magnet: 58x13x15mm
- Weight: 32.5 g
- Magnet Sensor Gap Activated: 10mm
- RF Operating Distance: 30m* (indoor)
- Power Supply: 3V (AAAx2,alkaline batteries recommended)
- Battery Life: 1 year* (Triggered twenty times a day)
- Operating Temperature: 0 ~ 40 (32 ~ 104)
*Actual operating distance and battery life may vary with the usage
patterns and operating environment.
The device is suitable for indoor use only. No water resistance.
When low battery, the LED will blink and cannot for pairing.
- Frequency: 2.4G Hz
Specification
5
1 cm (max)
3
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution
To comply with FCC RF exposure compliance requirements, a separation distance of at least 20
cm must be maintained between the antenna of this device and all persons.
This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
2
1
3
2
1
3
5 6
7 8
1 2
3 4
ENGLISH
FRANÇAIS
ESPAÑOL
DEUTSCH
ITALIANO
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Switel DWM001 RF Door- Window Sensor - BSW220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Switel DWM001 RF Door- Window Sensor - BSW220 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info