555283
6
Zoom out
Zoom in
Previous page
1/74
Next page
6
Circular saw
INTENDED USE
This tool is intended for lengthways and crossways cutting
of wood with straight cuts as well as angle cuts to 45°; with
the appropriate saw blades also non-ferrous metals, light
building materials and plastics can be cut
TECHNICAL SPECIFICATIONS 1
PRODUCT ELEMENTS 2
1. Handle
2. On/Off switch
3. Cutting depth adjusting lever
4. Lower guard
5. Blade bolt
6. Foot
7. Flange
8. Saw blade
9. Parallel guide
10. Parallel guide knob
11. Cutting angle adjusting knob
12. Laser On/Off switch
13. Spindle-lock button
SAFETY
WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
re and/or serious injury.
DANGER
Keep hands away from cutting area and the
blade; keep your second hand on front handle (if
both hands are holding the saw, they can not be cut by
the blade)
Do not reach underneath the workpiece (the guard
cannot protect you from the blade below the workpiece)
Adjust the cutting depth to the thickness of the
workpiece (less than a full tooth of the blade teeth
should be visible below the workpiece)
Never hold piece being cut in your hands or
across your leg (it is important to support the work
properly to minimize body exposure, blade binding, or
loss of control)
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord (contact with a
“live” wire will also make exposed metal parts of the tool
“live” and shock the operator)
When ripping always use a rip fence or straight
edge guide (this improves the accuracy of cut and re-
duces the chance for blade binding)
Always use blades with correct size and shape of
arbor holes (diamond or round) (blades that do not
match the mounting hardware of the saw will run ec-
centrically, causing loss of control)
Never use damaged or incorrect blade washers
or bolts (the blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation)
English
KICKBACK-CAUSES
Kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece toward the operator
When the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator
If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the wood causing the blade to climb out
of the kerf and jump back towards operator
KICKBACK - OPERATOR PREVENTION
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below
Maintain a rm grip with both hands on the saw
and position your arms to resist kickback forces;
position your body to either side of the blade, but
not in line with the blade (kickback could cause the
saw to jump backwards, but kickback forces can be
controlled by the operator, if proper precautions are
taken)
When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to
a complete stop; never attempt to remove the saw
from the work or pull the saw backwards while the
blade is in motion or kickback may occur (investigate
and take corrective actions to eliminate the cause of
blade binding; avoid cutting nails or screws)
When restarting a saw in the workpiece, centre
the saw blade in the kerf and check that saw teeth
are not engaged into the material (if saw blade is
binding, it may walk up or kickback from the workpiece
as the saw is restarted)
Support large panels to minimize the risk of blade
pinching and kickback (large panels tend to sag under
their own weight; supports must be placed under the
panel on both sides, near the line of cut and near the
edge of the panel)
Do not use a dull or damaged blade (unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback)
Blade depth and bevel adjusting locking levers
must be tight and secure before making cut (if blade
adjustment shifts while cutting, it may cause binding and
kickback)
Use extra caution when making a plunge cut into
existing walls or other blind areas (the protruding
blade may cut objects that can cause kickback)
WARNING
Check lower guard for proper closing before each
use
Do not operate the saw if lower guard does not
move freely and close instantly
Never clamp or tie the lower guard into the open
position
If saw is accidentally dropped, lower guard may be
bent; raise the lower guard with the retracting handle
and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stomer SCS-185 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stomer SCS-185 in the language / languages: All languages as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info