Manual Stiga 107M (page 7 of 11) (English)

608619

Zoom out

Zoom in

1/11

ENGLISH

3.2 Installation of 107 M HD, 121 M

1. Place the cutting deck in position in front of the

machine.

2. Install the following components on both wheel

axles:

• Washer (3:B).

• Deck mount (3:C).

• Washer (3:B).

• Circlip (3:A).

3. Remove the pins on both sides. See fig. 7:I and

fig. 13.

4. Screw the arms into each other. See fig. 4.

5. Suspend the cutting deck in the implement lift-

er. See fig. 14.

6. If the deck has electrical cutting height adjust-

ment, connect the cable to the machine’s front

right socket. See fig. 15.

3.2.1 Belt, 107 M HD, 121 M

The cutting deck’s rear section should rest on the

floor (it should not be lifted or secured).

Install the belt as follows:

1. 107 M HD

: Set the maximum cutting height.

121 M

: Set the cutting height in the centre posi-

tion

2. Remove the belt cover. See fig. 8 and 10. The

number in the figure indicates the key width.

3. Locate the belt around the machine’s belt pulley

(16:M).

4. Force the belt onto the cutting deck’s belt pul-

ley.

5. Grip the belt tensioner’s lever with your left

hand. Pull the lever and apply the tensioner to

the outside of the belt with your right hand. See

fig. 16.

6. Fit the belt cover. See fig. 8 and 10.

7. Lift up and secure the rear section of the cutting

deck.

107 M HD on machines with 17” wheels:

Install

the pins in the third hole from the top. See fig.

13.

107 M HD on machines with 16” wheels:

Install

the pins in the fourth hole from the top. See fig.

13.

121 M: Lift up and install the pins (7:I).

3.3 Installing 107 M

1. Place the cutting deck in position in front of the

machine.

2. Install the following components on both wheel

axles:

• Washer (11:B).

• Deck arm (11:D).

• Washer (11:B).

• Circlip (11:A).

3. Install the deck arms in the cutting deck’s front

corners. After tightening, it should be possible

to move the rear section of the cutting deck free-

ly up and down.

4. Suspend the cutting deck in the implement lift-

er. See fig. 14.

3.3.1 Belt, 107 M

The cutting deck’s rear section should rest on the

floor (it should not be lifted or secured).

Install the belt as follows:

1. Set the maximum cutting height.

2. Remove the belt cover. See fig. 10. The number

in the figure indicates the key width.

3. Locate the belt around the machine’s belt pulley

(16:M).

4. Force the belt onto the cutting deck’s belt pul-

ley.

5. Grip the belt tensioner’s lever with your left

hand. Pull the lever and apply the tensioner to

the outside of the belt with your right hand. See

fig. 16.

6. Fit the belt cover. See fig. 10.

7. Lift up the cutting deck so that it locks in the

catches (12:L).

3.4 Tyre pressure

Adjust the air pressure in the tyres as follows:

Front: 0.6 bar (9 psi).

Rear: 0.4 bar (6 psi).

3.5 Basic setting

In order for the cutting deck to cut optimally, the

correct basic setting is required. The deck is in the

basic setting when its rear edge is 5 mm above its

front edge. This means that the deck is inclined

forwards.

Carry out basic setting as described below.

3.5.1 Basic setting, 125 Combi Pro, 107 M

The deck is in the basic setting when the actions

under 3.1.1 and 3.2.1 have been carried out.

3.5.2 Basic setting, 107 M, 121 M

See fig. 17 and perform basic setting of 107 M and

121 M as follows:

1. Place the machine on a level floor.

Requirements for floor flatness: ±1 mm/m. No

slope towards a floor drain or similar may occur

in front of or behind the machine.

2. The tyres must have the correct air pressure.

See 3.4.

3. Place the deck in transport position and lay a

plane-parallel plank under the deck.

4. Place a 5 mm tall spacer on the plank under the

rear edge of the cutting deck, and lower the

deck to the working position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga 107M in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga 107M Manual

Product: