682525
48
Zoom out
Zoom in
Previous page
1/52
Next page
48 Sterling Elite2 XS-RS-Plus
18.2 WHEEL REMOVAL
WARNING!
It is not usually practical to try to repair a puncture in •
situ at the site of the occurrence. Sunrise Medical
suggest that you call for help to remove the scooter
either directly to an approved service agent, or to a
safe place for collection by the approved agent at a
later time.
If you are in any doubt about the servicing •
requirements of your scooter contact your Sunrise
Medical authorised dealer.
Do not attempt any task you are not sure of.•
Do not attempt a puncture repair if the scooter has •
stopped in an unsafe area. Move the scooter to a
safe area away from traffic and other hazards.
Do not attempt a puncture repair in busy pedestrian •
areas.
Do not attempt a puncture repair if the scooter is •
causing an obstruction.
If you are using a jack or other equipment, always •
follow the user instructions given in the related
Owners’ Manual or User Instructions.
Be aware that the scooter may fall off the jack at any •
time.
Keep hands and feet clear of the scooter when it is •
on the jack.
Do not stand the jack on uneven surfaces.•
Always use a support block or stand in conjunction •
with the jack.
The scooter must be in drive mode with the power •
switched OFF and the keys removed, before jacking
any wheel off the ground.
Do not raise more than one wheel of the ground at •
any one time.
NOTE: Reverse the following procedures to refit the
wheels unless otherwise stated.
18.2.1 ELITE2 XS RS 3-Wheel Front Wheel Removal
Elevate the front wheel by placing a jack under the •
relevant jack points, (Fig.18.1).
When elevated back up the jack with solid blocks to •
increase stability, (Fig18.11).
Use a 4.0mm Allen Key to remove the brake anchor •
stud, (Fig.18.2).
Remove the brake cable from the outer sleeve by •
turning the knurled wheel until the slots align,
(Fig.18.3).
Lift the brake nipple out of the brake actuator arm, •
(Fig.18.4).
Use a 19.0mm Socket and 10.0mm Allen key to undo •
the nut, (Fig.18.5).
Start to withdraw the axle stud slowly, (Fig.18.6).•
First the washers will drop out, (Fig.18.7).•
Next lift the Brake assembly away from the hub, •
(Fig.18.8).
The spacer falls away, (Fig.18.9).•
Remove the front wheel assembly, (Fig.18.10).•
= JACK POINTS
Fig.18.1
Fig.18.2 Fig.18.3
Fig.18.4 Fig.18.5
Fig.18.6 Fig.18.7
Fig.18.8 Fig.18.9
Fig.18.10
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sterling Elite 2 XS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sterling Elite 2 XS in the language / languages: English as an attachment in your email.

The manual is 3.6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sterling Elite 2 XS

Sterling Elite 2 XS User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info