593128
79
Zoom out
Zoom in
Previous page
1/81
Next page
- 156 - - 157 -
该设备配备了一个 2 级式热保护装置:
1
.
切断 。但
屏上通过三角警示符号提醒加热器已关闭。
后达到出风口温度所需时间会比平常要长。*
2.
超负荷工作时,温度安全装置将完全关闭设备。
* 仅针对 HL 2020 E
为了您的安全
设备说明 - 调试
请注意至加工物件的距离取决于物件材料和所采用的加
工方式。每次使用前务必进行空气量和温度测试!无论
目标是点还是平面,热风都可借助配件中的可插拔喷嘴
组(参见封面上的配件侧)进行精准控制。喷嘴温度极
高,更换时须小心!将热风机作为立式设备使用时,请
注意其放置状态应稳固防滑,并应确保底台干净。
HL 1620 S
设备通过手柄背面的分档开关 (7) 开启和关闭。空气量
和温度有两个设置档位。第 1 档的温度为 300 °C
240 l/min 2 500 °C
450 l/min
该设备仅供家庭使用。
HL 1920 E
设备通过手柄背面的分档开关 (7) 开启和关闭。除了三
档转速/空气量调节(第 1 档是 80 °C 的冷空气档)之
外,第 2 档和第 3 档的温度还可以在 80 °C–600 °C
的范围内通过调节轮 (8) 无级调节。调节轮上显示的数
1 - 9 可供参考。»1« 表示 80 °C»9« 表示最高温度
600 °C。三个档位的空气量分别为 150/150-300/300-
500 l/min。保护管 (3) 可通过一个卡口接头取下。
HL 2020 E
设备通过手柄背面的分档开关 (7) 开启和关闭。除了通过开
(7) 调整三档转速/气量之外还可以通过键控侧板开关 (9)
80 630的范围内在 2 档和 3 上对温度进行无
调整。可以通过按动键控侧板开关 (9) 右侧的“+”号以
1
0
°C
步阶提高目标温度或通过按动键控侧板开关(9)
侧的“-”号以 10
°C 的步阶降低目标温度短按翘板开
每次可提高或降低目标温度 10 °C。长按翘板开关则
10 °C 的增量连续提高或降低温度,直至松开翘板
关或达到最低或最高温度。设置的额定温度可在显示屏
上显示 3 秒。温度降低或升高期间,显示屏将显示送风
管上的实际温度。该时间段内 °C/°F 图标闪烁。一
旦达到额定温度,该图标将恒定显示在显示屏上。
风机第 1 档的温度为 80 °C从温度较高的热风机
2 档或3 档切换至第 1 档时,设备需要少许时间冷
80 °C冷却过程中,LCD 显示屏 (10) 会显示
风口的实际温度。设备关闭后会保留最后一次设置的数
值。保护(3) 通过一个卡口接头取下。
更换电缆(仅限 HL 2020 E
如果电源线损坏,无需打开外壳即可轻松将其更换:
1. 重要!断开设备的电源。
2. 松开螺钉 并取下盖板
3. 松开拉力解除装置
4. 松开电源接线端
5. 拔出电缆
6. 插入新的电缆并按照相反顺序(首先拧紧第 1 个电源
接线端等)重新固定。
c
d
a
b
e
14
技术参数
HL 1620 S
HL 1920 E
HL 2020 E
220-230 V50/60 Hz
2200 W
12 3
150 150-300 300-500
80 80-630
通过按键以 10 °C 的增量无
级调节
LCD 显示屏
II
≤ 70dB (A)
≤ 2.5 m/s
2
/
K = 0.08 m/s
2
0.880 Kg
220-230 V50/60 Hz
2000 W
12 3
150 150-300 300-500
80 80-600
通过调节轮
9 段无级调节
II
≤ 70dB (A)
≤ 2.5 m/s
2
/
K = 0.08 m/s
2
0.840 Kg
220-230 V50/60 Hz
1600 W
12
240 450
300 500
II
≤ 70dB (A)
≤ 2.5 m/s
2
/
K = 0.08 m/s
2
0.670 Kg
电源连接
功率
档位
空气量 (l/min.)
温度 (°C)
温度设置
温度显示
余热指示灯
防护等级
(无地线连接)
热保护切断装置
温度安全装置
声压级
振动总值
重量
保留技术更改的权利!
安全性提示
只能由专业电工进行维修作业。
该电动工具符合相关安全性条款。
维修作业只能由专业电工进行,否则
可能导致意外发生。设备电源线损坏
时,须由制造商或其客服人员及具有
相关资质的人员进行更换,以防止发
生危险。
余热指示灯 (仅限 HL 2020 E)
余热指示灯仅用作光学警告提示,以
免皮肤直接接触送风管时造成受伤。
电源线拔下后,余热指示灯仍工作!
运行 90 秒后,指示灯将开始工作,并
且持续闪烁,直至室温下送风管的温
度降到 60 °C 以下。
如果设备运行时间少于 90 秒,则余热
指示灯无法激活。任何情况下均由用
户承担责任,使用热风机时务请格外
小心谨慎。
请将本安全性提示妥善存放在设备附
近。
79


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel HL 1920E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel HL 1920E in the language / languages: All languages as an attachment in your email.

The manual is 4,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info