593372
79
Zoom out
Zoom in
Previous page
1/81
Next page
- 156 - - 157 -
余热指示灯
余热指示灯仅用作光学警告提示,
以免皮肤直接接触热送风管时造成
受伤。电源线拔下后,余热指示灯
仍工作!
运行90秒后,指示灯将开始工
作,并且持续闪烁,直至室温下送
风管的温度降到60℃以下。如果
设备运行时间少于90秒,则余热
指示灯无法激活。任何情况下均由
用户承担责任,因为使用热风机时
应格外小心谨慎。
请将本安全性提示妥善存放在设备
附近。
该设备配备了一个热保护装置:
超负荷工作时,热熔断路器将完全关闭设备。
为了您的安全
设备说明 - 调试
请注意:与加工物件的距离取决于物件材料以及所采用的加
工方式。使用前请您务必进行空气量测试和温度测试。使用
作为配件的可插拔喷嘴组(参见封面上的配件页),可以使
热风精确控制点或面的操作。
喷嘴温度极高,更换时须小心!将热风机作为立式设备使用
时,请注意其放置状态应稳固防滑,并应确保底台干净。
1. 调试
设备通过开关键
8
来控制手柄背面的开关。操纵杆
9
于控制温度和空气量以及风扇转速。
2. 温度设置
通过在带有LCD显示屏的操作面板中对操纵杆进行操作,温
度可以在 50-700 摄氏度之间进行调节。测量通风管出口处
的实际温度并显示在显示屏中。操纵杆
9
相当于带有+/-功
能的回车键。
迅速按下“+/-”操纵杆,可以10°一级升高或降低设置值。
长时间按下操纵杆可以更快达到温度值。如果已设置为所需
温度,则风机需要持续运行数秒(这取决于所选择的的转速/
空气量),以便达到设置值。显示屏将显示已设置的额定温
度,持续 3 秒。随后,其将显示当前实际温度。达到额定温
度前,"°C/°F" 图标将持续闪烁。
如需重新设置温度,则仅需重新移动操纵杆,即可轻松升高
或降低数值。热风机关闭后会保留最后设置的数值。
3. 设置空气量
首先按下空气量模式按键,以改变
10
空气量;通风设备符
号闪烁。随后,通过操纵杆进行设置。如果 5 秒内未执行
更改空气量的操作,将自动退出空气量设置模式。空气量设
置完后,重新按下空气量按键,这样可以立即退出空气量设
置模式。空气量 的变化范围 范围为最低 150 l/min 至最高
500 l/min
工件温度感应
工件温度感应我们推荐您使用STEINEL 温度扫描仪
HG Scan PRO(型号:007553)。
程序运行 [P]
出厂时,针对最常见的工作设置了四种程序。按下程序运行
按键“P”。显示的数字1,表示程序1。继续按下程序按键
以切换至程序2-4。再次按键以回到正常运行状态。
安全性提示
预设程序
保存功能[S]
可随时更改并保存四项程序的数值。为此,首先按下程序按
键“P”,
11
, 直至显示改变程序。然后设置所需的温度和
空气量。LCD的保存图标
闪烁表示,所选择的用户程序
已更变。按下并按住程序选择按键以保存所选用户程序中的
设置。保存图标继续闪烁大约 2 秒。如果保存图标持续亮
起,则表示输入值已经保存在程序中。按下程序键直至显示
屏中的程序图标消失,即返回正常功能。
微尘过滤器
HG 2620 E 具有一个集成的微尘过滤器
3
。清洁时(使用
压缩空气),拆下螺丝,移开保护层,移除过滤器。
更换电缆
如果电源线损坏,无需打开外壳即可轻松将其更换:
1. 重要!断开设备的电源。
2. 松 开
d
螺丝并取下
a
盖板。
3. 松开
b
张力释放装置。
4.松开
c
电源接线端。
5. 拔出
e
电缆。
6. 插入新的电缆并按照相反顺序(拧紧第一个电源接
线端等)重新固定。
更换供暖设备
插入HG 2620 E 供暖设备并且通过几个手柄进行更换。
1. 重要!断开设备的电源。
2. 拧下保护管螺丝(图1)。
3. 移除保护管(图1)。
4. 拧下通风管末端的四个螺丝(图2)。
5. 取下供暖设备并更换新的供暖设备(图2/3)。
6. 重新拧紧供暖设备(图3)。
7. 拧紧保护管(图4)。
维护
维修
a
a
12
14
3
1.
3.
2.
4.
重新启动保护
供电中断后,重新启动保护会阻碍热风机的意外启动。仅通
过开关键的重新按入
8
可以使热风机再次投入使用。
LOC-功能
HG 2620 E 的锁定改写控制功能(LOC)是用于避免不经意间
更改已选择的设置。若想设置如LOC功能的有关事宜,请拨
+86 21 5820 4486 联系我们的客服。
其他功能
程序 温度 空气 l/min
1 大约250 350
2
大约350 400
3
大约450 500
4
大约550 400
79


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel HG2620 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel HG2620 E in the language / languages: All languages as an attachment in your email.

The manual is 18,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info