593374
6
Zoom out
Zoom in
Previous page
1/8
Next page
- 10 - - 11 -
Stainless steel outlet nozzle
Removable guard sleeve
Air inlet with integrated fine dust filter
Soft coating for non-slip standing
Heavy-duty rubber-insulated power cord
Multiple-stage switch for adjusting airflow (2-stage)
Thumbwheel for setting temperature
Soft grip handle for comfortable operation
Replaceable mains power cord
Protect the power cord from heat,
oil and sharp edges.
Beware of toxic gases and
fire hazards.
Toxic gases may occur when work-
ing on plastics, paints, varnishes or
similar materials.
Beware of fire and ignition hazards.
For your own safety, only use ac-
cessories and attachments that are
specified in the operating instructions
or recommended or specified by the
tool manufacturer.
Using attachments or accessories
other than those recommended in
the operating instructions or cata-
logue may result in personal injury.
Repairs must only be
carried out by a qualified
electrician.
This electric power tool complies
with the relevant safety regulations.
Repairs should only be performed by
a qualified electrician. Otherwise the
user may run the risk of accidents.
Keep these safety precautions
with the tool.
Store your tools in a
safe place.
After use, set the tool down on its
standing surface and let it cool
before putting it away.
When not in use, tools must be
stored in a dry, locked room out of
children‘s reach.
This tool may be used by children
aged 8 or above and by persons
with reduced physical, sensory or
mental capabilities or lack of experi-
ence and knowledge if they are
supervised or have been given in-
structions on how to use the tool
safely and understand the hazards
involved.
Do not allow children to play with
the tool.
Children are not allowed to clean or
carry out maintenance work on the
tool without supervision.
Do not overload
your tools.
Your work results and safety will be
enhanced if you operate the tool
within the specified output range.
After using the tool for a prolonged
period at maximum temperature,
you should reduce the temperature
before switching the tool off. This will
prolong the service life of the heating
element. Do not carry the tool by
the power cord. Do not unplug the
tool by pulling on the power cord.
Safety warnings
These hot air tools are doubly protected from
overheating:
The thermal cut-out completely shuts down the tool
if it is overloaded.
For your safety
Tool description - Operation
Please note: The distance from the object you are working
on depends on material and intended method of working.
Always try out the airflow and temperature on a test piece
first. Using the attachable accessory nozzles (see accesso-
ries page on the cover) the flow of hot air can be controlled
with maximum precision.
Take care when changing hot nozzles! When using the
hot air tool in the self-resting position, make sure it is stand-
ing on a stable, non-slip and clean surface.
The tool is switched on and off by means of a two-stage
airflow switch
6
. In settings 1 and 2, the temperature is
continuously variable at a thumbwheel in 9 steps. The guard
sleeve can be removed.
Switching on causes brief voltage drops. If the mains power
supply system is not absolutely stable, other equipment may
be affected. No disturbance is likely to occur with mains
impedances of less than 0.43 ohms.
Tool features
1
2
3
4
6
7
8
5
9
Changing the power cord
9
If the power cord needs changing, this can easily be done
without opening the casing:
1. Important! Disconnect tool from power supply.
2. Undo screw
a
and pull off cover cap
b
.
3. Release cable grip
c
.
4. Undo mains terminals
d
.
5. Pull out cable
e
.
6. Insert new cable and secure in reverse order
(1. Firmly screw down mains terminals etc.).
Repair
Fine dust filter
The HG 2220 E / HG 2420 E has an integrated fine dust
filter
3
. To clean it (with compressed air), undo screws (a),
take off cover and remove filter.
Maintenance
a
a
GB
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel HG 2420 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel HG 2420 E in the language / languages: All languages as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info