592489
5
Zoom out
Zoom in
Previous page
1/51
Next page
- 8 -
Betriebsstörungen
SensorLeuchte
ohne Spannung
SensorLeuchte
schaltet nicht ein
SensorLeuchte
schaltet nicht aus
SensorLeuchte schaltet
ohne erkennbare Bewegung ein
SensorLeuchte schaltet trotz
Bewegung nicht ein
Störung
Haussicherung defekt, nicht
eingeschaltet,
Leitung unterbrochen
Kurzschluss in der Netzzuleitung
Eventuell vorhandener
Netzschalter aus
neue Haussicherung,
Netz schalter einschalten,
Lei tung überprüfen mit
Spannungsprüfer
Anschlüsse überprüfen
Netzschalter einschalten
Dämmerungseinstellung
falsch gewählt
Leuchtstofflampe defekt
Netzschalter AUS
Haussicherung defekt
neu einstellen
Leuchtstofflampe austauschen
einschalten
neue Haussicherung,
evtl. Anschluss überprüfen
dauernde Bewegung im
Erfassungsbereich
Bereich kontrollieren
Leuchte nicht erschütterungsfrei
montiert
Bewegung lag vor, wurde
jedoch vom Beobachter nicht
erkannt (Bewegung hinter
Wand, Bewegung eines klei-
nen Objektes in unmittelbarer
Lampennähe etc.)
Gehäuse fest montieren
Bereich kontrollieren
schnelle Bewegungen werden
zur Störungsmini mierung unter-
drückt oder Erfassungsbereich
zu klein eingestellt
Bereich kontrollieren
Ursache Abhilfe
- 9 -
Dear Customer,
Congratulations on purchasing your new STEINEL
IndoorSensorLight and thank you for the confidence
you have shown in us. You have chosen a high-qual-
ity product that has been manufactured, tested and
packed with the greatest care.
Please familiarise yourself with these instructions
before attempting to install the light because pro-
longed reliable and trouble-free operation will only be
ensured if it is fitted properly.
We hope your new STEINEL IndoorSensorLight will
bring you lasting pleasure.
GB
System components
Base
HF-sensor with setting controls
Sealing plug
Cover
Support plate
Hinged clip
Twilight setting
Time setting
Reach setting
Mounting bracket
Mounting clamp
Mains connection, concealed wiring
Mains connection, exposed wiring
Principle
The SensorLight is an active motion detector. The
integrated HF-sensor emits high-frequency electro-
magnetic waves (5.8 GHz) and receives their echo.
The sensor detects the change in echo from even
the slightest movement in the light's detection zone.
A microprocessor then triggers the "switch light
ON" command. Detection is possible through doors,
panes of glass or thin walls.
Detection zones for ceiling mounting:
1) Minimum reach (1 m dia.)
2) Maximum reach (8 m dia.)
Detection zones for wall mounting:
3) Minimum reach (1 m dia.)
4) Maximum reach (8 m dia.)
Important: Persons or objects moving towards the
light are detected best.
Safety warnings
Disconnect the mains power before attempting any
work on the unit!
During installation, the electric power cable to be
connected must be voltage-free. Therefore, switch
off the power first and use a voltage tester to make
sure the wiring is off circuit.
Installing the IndoorSensorLight involves work on
the mains voltage supply. This work must therefore
be carried out by a qualified electrician in accord-
ance with applicable national wiring regulations and
electrical operating conditions.
(D - VDE 0100,
A -ÖVE-ÖNORM E8001-1, - SEV 1000)
Only use genuine replacement parts.
Repairs must only be made by specialised work-
shops
Disconnect the light from the power supply before
changing the tube.
Note:
The high-frequency output of the HF-sensor is
approx. 1 mW – that's just one 1000th of the
transmission power of a mobile phone or the
output of a microwave oven.
approx. 1 mW
approx. 1000 mW
- 9 -
I
II
Installation instructions
GB
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel FRS 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel FRS 30 in the language / languages: All languages as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info