619114

StarTrac 7080 Series - Spinner Elite Manual

29
Zoom out
Zoom in
Previous page
1/30
Next page
! 

ADJUSTMENTS
C
HAIN
T
ENSION &
A
DJUSTMENT
The chain on your bike has been factory set and lubricated. It should not require adjustment initially. Over time, however, you may need to adjust the
tension.
CAUTION: Improper chain adjustment will cause premature wear and may void the warranty.
To adjust chain on Spinner
®
V:
1. Using a 3mm Allen Wrench, remove the three screws supporting the
plastic chain guard shroud.
2. With an adjustable wrench, loosen the two nuts on both sides of the
flywheel (Figure 1 & 2).
3. Tighten the two bolts that go through the frame, moving the flywheel
forward by turning clockwise, until there is approximately 3/16” of slack
in the chain (Figure 1 & 2).
4. Re-tighten the two bolts on both sides of the flywheel and replace the
chain guard shroud.
NOTE: If the chain is too tight, typically the rider will feel a strong
vibration between 20 and 50 RPMs. If this happens, loosen the bolts 1/2”
turn until the vibration disappears, then tighten the lock nuts.
Figure 1.
Chain guard side (View shows chain guard shroud
removed)
Figure 2.
Other side opposite of chain
To adjust chain on Spinner
®
Pro / Elite / NXT:
1. Using a 3mm Allen Wrench, remove the three screws supporting the
plastic chain guard shroud. (Figures 3 & 4)
2. Using a 16mm or 5/8” socket and socket wrench, loosen the axle nuts
on both sides of the flywheel.
3. Using a 10mm open end wrench, loosen the lock nuts on the chain
adjustment screws.
4. To tighten the chain, turn the adjustment screw in a clockwise rotation
equally on both sides using the 10mm open end wrench. (Figure )
5. To loosen the chain, turn the adjustment screws on both sides counter-
clockwise using a 10mm open end wrench.
6. While adjusting the chain tension, work on both sides of the flywheel.
Adjust the angle of the flywheel so it is straight front to rear and evenly
spaced within the frame side to side. (Figure )
7. Align the chain so it runs straight on both of the sprockets.
 

Figure 3. Pro Figure 4. NXT
… 29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for StarTrac 7080 Series - Spinner Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of StarTrac 7080 Series - Spinner Elite in the language / languages: English as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info