Manual Stanley STHT1-12185 -APC-2IN1 (page 5 of 130) (All languages)

622190

Zoom out

Zoom in

1/130

m SAFETY AND OPERATION MANUAL

Stanley tools are precision built. They will deliver efficient,

dependable service when used correctly and with care. As

with any fine power tool, the manufacturer’s instructions

must be followed for best results. Please study this manual

and understand the safety warnings and cautions before

operating the tool. The instructions on installation, operation

and maintenance should be read carefully and the manuals

kept for reference. Note: Additional safety measures may be

required because of your particular application of the tool.

Contact your Stanley representative or distributor with any

questions concerning the tool and it’s use.

NOTE:

Stanley tools have been designed to provide excellent

customer satisfaction and are designed to achieve maximum

performance when used with precision Stanley fasteners

engineered to the same exacting standards.

Stanley cannot assume responsibility for product

performance if any of our tools are used with fasteners

or accessories not meeting the specific requirements

established for genuine Stanley nails, staples and

accessories.

LIMITED WARRANTY

Stanley Inc., warrants to the original retail purchaser that this

product is free from defects in material and workmanship, and

agrees to repair or replace, at Stanley’s option, any defective

product within 90 days from the date of purchase. This

warranty is not transferable. It only covers damage resulting

from defects in material or workmanship, and it does not

cover conditions or malfunctions resulting from normal wear,

neglect, abuse or accident.

THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS

WARRANTIES. ANY WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE

DURATION OF THIS WARRANTY.

STANLEY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

Some countries do not allow limitations on how long an

implied warranty lasts, or the exclusion or limitation of

incidental or consequential damages, so the above limitations

or exclusions may not apply to you. This warranty gives you

specific legal rights, and you may also have other rights

which vary from state to state or from country to country.

To obtain warranty service, you must return the product at

your expense together with proof of purchase to a Stanley

regional warranty repair center.

SPECIAL REFERENCES

Only those fasteners that are specified in the operating

instructions (see Tool Technical data) should be used in the

tool. The tool and the specified fasteners are to be considered

as one single safety system for safety purposes.

Repairs shall only be carried out by the authorized agents of

Stanley or by other experts, giving due regard to the safety,

operating and maintenance instructions in this manual, the

specific tool manual and in the Tool Technical Data.

Note: Experts are those who, as a result of professional

training or experience, have acquired sufficient expertise in

the field of fastener driving tools as to be able to assess the

safe condition of fastener driving tools.

m SAFETY INSTRUCTIONS

EYE PROTECTION which

provides protection against

flying particles both from

the FRONT and SIDE should always be

worn by the tool operator and others in

the work area when loading, operating

or servicing this tool. Eye protection is

required to guard against flying fasteners

and debris, which could cause severe

eye injury. The employer and/or user must

ensure that proper eye protection is worn.

Eye protection in accordance with 89/686/EEC, and with

equal or greater grade than defined in EN166 should be

used. However all aspects of operators work, environment

and other type/s of machinery being used, should also

be considered when selecting any personal protection

equipment.

CAUTION: ADDITIONAL SAFETY PROTECTION may be

required in some environments. For example, the working

area may include exposure to noise levels that can lead to

hearing damage.

SAFETY INSTRUCTIONS FOR AIR SUPPLY AND CONNECTIONS

When connecting tools to the air supply, the fastener discharge

area of the tool should be pointed away from the operator and

others in the working area. Place the discharge area of the tool

over a test piece of material of sufficient thickness which will

fully accommodate the dimensions of the fastener to be driven.

With hands clear of the trigger and trip mechanism, limbs and

body clear of the discharge area the tool the air supply may now

be connected.

l

Do not use oxygen and combustible gases as an energy

source for pneumatically operated tools.

l

Do not use bottled gases or an air supply where the

maximum pressure in the line can potentially exceed 9.6

Bar as the tool may burst, possibly causing injury. If the

maximum air supply pressure could exceed these pressures,

then a pressure reducing valve with a downstream safety

valve shall be built into the air supply.

l

Do not pull the trigger or depress the safety trip while

connecting to the air supply. The tool could cycle, possibly

causing injury.

l

The connector on the tool must not hold pressure when the

air supply is disconnected. If a wrong fitting is used, the

tool can remain charged with air after disconnecting and

thus will be able to drive a fastener even after the air line is

disconnected possibly causing injury.

l

Always disconnect air supply: 1) Before making adjustments;

2) When servicing the tool; 3) When clearing a jam; 4) When

tool is not in use; 5) When moving to a different work area,

as accidental actuation may occur, possibly causing injury.

m SAFETY INSTRUCTIONS FOR LOADING TOOL

When loading the tool 1) Never place a hand or any part of the

body in fastener discharge area of the tool; 2) Never point the

tool at self or anyone else; 3) Do not pull the trigger or depress

the safety trip as accidental actuation may occur, possibly

causing injury.

FT72124-a-0611_Tool_Manual_AW.indd 5 05/07/2011 17:01

I have just bought a brad nailer model STHT1-12184 (APC-BC). According to Screwfix catalogue this gun accepts their 16ga Brad nails.(Screwfix ref 91803). I thought you could only use a max 18gauge with this tool or am I wrong? Submitted on 1-4-2019 at 15:38
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT1-12185 -APC-2IN1 in the language / languages: All languages as an attachment in your email.

The manual is 3,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley STHT1-12185 -APC-2IN1 Manual

Product: