720459
6
Zoom out
Zoom in
Previous page
1/9
Next page
6
ENGLISH
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle
Turn the grip counterclockwise until you can slide the
side handle (6) onto the front of the tool.
Rotate the side handle into the desired position.
Tighten the side handle by turning the grip clockwise.
Warning! Alaways use the tool with the side
handle properly assembled.
Fitting an accessory (fig.A)
Clean and grease the shank (8) of the accessory.
Pull back the sleeve (9) and insert the shank into the tool
holder (5).
Push the accessory down and turn it slightly until it fits
into the slots.
Pull on the accessory to check if it is properly locked.
The hammering function requires the accessory to be
able to move axially several centimetres when locked in
the tool holder.
To remove the accessory, pull back the sleeve (9) and
pull out the accessory. tool holder.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Selecting the operating mode (fig. B)
The tool can be used in three operating modes. Press in the
button (10) and rotate the drilling mode selector (4) towards
the required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, set the
operatingmode selector (4) to the position.modes.
Hammer Drilling
For hammer drilling in masonry and concrete, set the
operating mode selector (4) to the position
When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
For hammering with spindle lock, and for light chiselling
and chipping set the operating mode selector (4) to the
position
Make sure the forward/reverse switch is in the forward
position.
When changing from hammer drilling to chiselling, turn
the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage
the spindle lock.
Warning! If your hammer is a 1 mode unit (STEL501), It
only has one function - hammer drilling. It can’t select
operating mode.
Selecting the direction of rotation
This function is included on only certain models
(STHR223K). For drilling, and for chiselling, use forward
(clockwise) rotation. For removing a jammed drill bit, use
reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse
slider (3) to the left.
To select reverse rotation, push the forward/reverse
slider to the right.
Warning! Never change the direction of rotation while the
motor is running.
Setting the drilling depth (fig. C)
Slacken the side handle (6) by turning the grip
counterclockwise.
Set the depth stop (7) to the desired position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
(Original instructions)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHR223 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHR223 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info