720425
7
Zoom out
Zoom in
Previous page
1/9
Next page
Setting the drilling depth (fig.B)
Slacken the side handle (7) by turning the grip counter
clockwise.
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
Switching on and off
To switch the tool on, press the variable speed switch(1).
The tool speed depends on how far you press the
switch. As a general rule, use low speeds for large
diameter drill bits and high speeds for smaller diameter
drill bits.
For continuous operation, press the lock-on button (2)
and release the variable speed switch. This option is
available only at full speed in both forward and reverse
modes.
To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation,
press the variable speed switch again and release it.
Maintenance
Your STANLEY power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Important
To ensure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment ( other than those listed in this
manual) should be performed by authorized service centers
or other qualified organizations, always –using identical
replacement parts inside.
Cleaning
Warning! Blow dirt and dust out the main housing
with dry air as often as dirt is seen collecting in and
around the air vents. Wear approved eye protection and
approved dust mask when performing this procedure.
Warning! Never use solvents or other harsh
chemicals for cleaning the non – metallic parts of
the tool. These chemicals may weaken the materials used in
these parts. Use a cloth dampened only with water and mild
soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Accessories
The performance of any power tool is dependent
upon the accessory used. STANLEY accessories
are engineered to high quality standards and are
designed to enhance the performance of power tool.
STANLEY offers a large selection of accessories available at
our local dealer or authorized service center at extra cost.
Caution: The use of any other accessory not
recommended for use with this tool could be hazardous.
Service Information
STANLEY offers a full network of company-owned and
authorized service locations throughout Europe. All
STANLEY Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
power tool service. Whether you need technical advice,
repair , or genuine factory replacement parts, contact the
STANLEY location nearest to you.
Notes
STANLEY’s policy is one of continuous improvement to
our products and, as such , we reserve the right to
change product specifications without prior notice.
Standard equipment and accessories may vary by
country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local STANLEY dealers for range
availability.
7
ENGLISH
(Original instructions)
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STDH6513 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STDH6513 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info