Manual Stanley SB90 (page 5 of 48) (English, French, Turkish)

720473

Zoom out

Zoom in

1/48

(Original Instructions) ENGLISH

b. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

c. Disconnect the plug from the power source and/

or remove the battery pack, if detachable from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tools operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

h. Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained

ADDITIONAL SPECIFIC SAFETY RULES

Safety instructions for belt sander

• Hold the power tools by insulated gripping

surfaces, because the sanding surface may contact

its own cord. Cutting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

opertator an electric shock..

• Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body leaves it unstable

and may lead to loss of control.

• Warning! Contact with or inhalation of dust arising from

sanding applications may endanger the health of the

operator and possible bystanders. Wear a dust mask

specifically designed for protection against dust and

fumes and ensure that persons within or entering the

work area are also protected.

• Thoroughly remove all dust after sanding.

• Take special care when sanding paint which is possibly

lead based or when sanding some woods and metal

which may produce toxic dust:

• Do not let children or pregnant women enter the work

area.

• Do not eat, drink or smoke in the work area.

• Dispose of dust particles and any other debris safely.

The intended use is described in this instruction manual.

The use of any accessory or attachment or performance of

any operation with this tool other than those recommended

in this instruction manual may present a risk of personal

injury and/or damage to property.

Additional safety information

WARNING: We recommend the use of a residual

current device with a residual current rating of

30mA or less.

SAFETY OF OTHERS

• This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the tool by a person responsible for

their safety.

• Children should be supervised to ensure that they do

not play with the appliance.

RESIDUAL RISKS

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These are:

– Impairment of hearing

– Risk of personal injury due flying particles.

– Risk of burns due to accessories becoming hot

during operation.

– Risk of personal injury due to prolonged use.

– Risk of dust from hazardous substances.

ELECTRICAL SAFETY

Your tool is double insulated; therefore no earth

wire is required. Always check that the main

voltage corresponds to the voltage on the rating

plate.

WARNING! If the power cord is damaged, it must

be replaced by the manufacturer, authorized

STANLEY Service Center or an equally qualified

person in order to avoid damage or injury. If the

power cord is replaced by an equally qualified

person, but not authorized by STANLEY, the

warranty will not be valid.

USING AN EXTENSION CABLE

If an extension cable is required, use an approved 3–core

extension cable suitable for the power input of this tool (see

Technical Data).The minimum conductor size is 1.5 mm2;

the maximum length is 30 m. When using a cable reel,

always unwind the cable completely.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SB90 in the language / languages: English, French, Turkish as an attachment in your email.

The manual is 1,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SB90 Manual

Product: