Manual Stanley FME790 (page 4 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720659

Zoom out

Zoom in

1/52

ENGLISH

(Original instructions)

Intended use

Your Stanley Fat Max FME790 mitre saw stand has been

designed for use with a Stanley Fat Max mitre saws. This tool

is intended for professional and private, non professional

users

Safety instructions

General safety warnings

Warning! Read all safety warnings and all

instructions.

u Read all of this manual carefully before using the

appliance.

u The intended use is described in this manual. The use of

any accessory or attachment or the performance of any

operation with this appliance other that those

recommended in this instruction manual may present a

risk of personal injury.

u Retain this manual for future reference.

Using your appliance

Always take care when using the appliance.

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure

that they do not play with the appliance.

u The appliance is not to be used as a toy.

u Use in a dry location only. do not allow the appliance to

become wet.

u Do not immerse the appliance in water.

u Do not open body casing. There are no user serviceable

parts inside.

u Do not operate the appliance in explosive atmospheres,

such as in the presence of ammable liquids, gases or

dust.

After use

u When not in use, the appliance should be stored in a dry,

well ventilated place out of the reach of children.

u Children should not have access to stored appliances.

u When the appliance is stored or transported in a vehicle it

should be placed in the boot or restrained to prevent

movement following sudden changes in speed or

direction.

Inspection and repairs

u Before use, check the appliance for damaged or defective

parts. Check for breakage of parts, damage to switches

and any other conditions that may affect its operation.

u Do not use the appliance if any part is damaged or

defective.

u Have any damaged or defective parts repaired or replaced

by an authorised repair agent.

u Never attempt to remove or replace any parts other than

those specied in this manual.

u In case of any missing parts, do not assemble the stand

until the missing parts are obtained and are correctly

installed.

Additional safety instructions for mitre saw stand

u Fully assemble and tighten all the fasteners required for

this stand. Also occasionally check the stand and make

sure the mitre Saw is still tight. An unstable loose stand

may shift in use and result in serious injury.

u Before operating, make sure the entire unit has been

placed on a at and solid level surface. If tool with stand is

unstable and tips, serious injury may occur.

u Never STAND on tool or its stand or use them as a ladder

or scaffolding. Serious injury could occur if the tool is

tipped or the cutting tool is contacted accidentally. Do not

store materials in a position on or near the tool where it

necessary to stand on the tool or its stand to reach them.

u Use only our replacement parts. Any others may cause a

hazard. The mitre saw should be mounted to the stand

rmly according to the instruction manual. Properly align,

position and balance the mitre saw according to the

instruction manual after mounting the mitre saw to the

stand.

u Never modify the stand in any manner or use the stand for

any purpose other than is stated in the instructions.

u Cutting material may cause the stand to become

unbalanced, always make sure the material is properly

supported. If the piece being cut is placed far beyond the

Work Support, the stand legs on the opposite side may be

lifted up suddenly due to weight imbalance. Firmly Hold

the opposite side before cutting to prevent this situation.

Warning! For your safety, never connect to power source until

all assembly steps are complete and you have read and

understood the entire owner’s manual.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When using

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME790 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FME790 Manual

Product: