622172
4
Zoom out
Zoom in
Previous page
1/68
Next page
4
ENGLISH
(Original instructions)
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualied repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety instructions for heat
guns.
Warning: Do not use outdoors, indoor use only.
Warning: This appliance must be placed on its stand when
not in use.
Warning: A re may result if the appliance is not used with
care, therefore be careful when using the appliance in places
where there are combustible materials.
u Do not apply heat to the same place for a long time.
u Do not use in presence of an explosive atmosphere.
u Be aware that heat may be conducted to combustible
materials that are out of sight.
u Place the appliance on its stand after use and allow it to
cool down before storage.
u Do not leave the appliance unattended when it is switched
on.
u Do not obstruct either the air intake slots or the nozzle
outlet as this may cause excessive heat build up resulting
in damage to the appliance.
u Do not direct the hot air ow at other people or animals.
u Do not touch the nozzle as it becomes very hot during use
and remains hot for up to 30 minutes after use.
u Do not place the nozzle against any object during or im-
mediately after use.
u Do not poke anything down the nozzle as it could give you
an electric shock.
u Do not look down the nozzle while the appliance is
switched on.
u Do not use the appliance as a hair dryer! The air tempera-
ture is far higher than a hardware.
u Ensure adequate ventilation during use as toxic fumes
may be produced.
u Do not use the appliance in a damp atmosphere.
u When stripping paint, ensure that the work area is
enclosed. Wear a dust mask specically designed for
protection against lead paint dust and fumes and ensure
that persons within or entering the work area are also
protected.
u Do not burn paint, as it could cause a re hazard.
u Do not allow paint to adhere to the nozzle as it could ignite
after some time.
u Switch off the appliance and allow it to cool before tting
any accessory.
Stripping lead-based paint
u Extreme care should be taken when stripping paint. The
peelings, residue and vapours of paint may contain lead,
which is poisonous. Any pre-1960 building may in the
past have been painted with paint containing lead. This
paint may be covered with additional layers of paint. Once
deposited on surfaces, hand to mouth contact can result in
the ingestion of lead.
u Exposures to even low levels of lead can cause irrevers-
ible brain and nervous system damage. The greatest
danger of lead poisoning is to children and pregnant
women.
u Before starting work, it is important to determine whether
the paint to be stripped contains lead. This can be done
using a test kit or by a professional decorator. Do not
smoke, eat or drink in a work area that could or may be
contaminated by lead. Lead based paints should only be
removed by a professional and should not be removed
using a heat gun.
Safety of others
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FME670 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME670 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info