Manual Stanley FME500 (page 5 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

622143

Zoom out

Zoom in

1/80

ENGLISH

(Original instructions)

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley Fat Max Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Tool holder

6. Side handle

7. Depth stop

8. Depth stop lock button

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle (g. C

u Turn the grip counterclockwise until you can slide the side

handle (6) onto the front of the tool.

u Rotate the side handle into the desired position.

u Tighten the side handle by turning the grip clockwise.

Fitting an accessory (g. A)

u Clean and grease the shank (9) of the accessory.

u Pull back the sleeve (10) and insert the shank into the tool

holder (5).

u Push the accessory down and turn it slightly until it ts into

the slots.

u Pull on the accessory to check if it is properly locked. The

hammering function requires the accessory to be able to

move axially several centimetres when locked in the tool

holder.

u To remove the accessory, pull back the sleeve (10) and

pull out the accessory.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Selecting the operating mode (g. B)

The tool can be used in three operating modes. Press in the

button (11) and rotate the drilling mode selector (4) towards

the required position, as indicated by the symbols.

Drilling

u For drilling in steel, wood and plastics, set the operating

mode selector (4) to the

position.

Hammer drilling

u For hammer drilling in masonry and concrete, set the

operating mode selector (4) to the

position

u When hammering, the tool should not bounce and run

smoothly. If necessary, increase the speed.

Hammering

u For hammering with spindle lock, and for light chiselling

and chipping, set the operating mode selector (4) to the

position.

u Make sure the forward/reverse switch is in the forward

position.

u When changing from hammer drilling to chiselling, turn

the chisel to the desired position. If resistance is felt

during mode change, slightly turn the chisel to engage the

spindle lock.

u When hammering with spindle lock, the angle of the bit

may be changed. Set the operating mode selector (4) to

the position, the angle of the bit may now be changed

by rotating the tool holder (6). Set the operating mode

selector (4) to the

position, before continuing.

Selecting the direction of rotation

For drilling, for tightening screws and for chiselling, use for-

ward (clockwise) rotation. For loosening screws or removing a

jammed drill bit, use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(3) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

Warning! Never change the direction of rotation while the

motor is running.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME500 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FME500 Manual

Product: