Manual Stanley FMCW210 (page 5 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720720

Zoom out

Zoom in

1/80

ENGLISH

(Original instructions)

Warning! Use this tool in a well ventilated area

when sanding ferrous metals. Do not operate

the tool near ammable liquids, gases or dust.

Sparks or hot particles from sanding or arcing

motor brushes may ignite combustible materials.

Warning! Do not sand magnesium! There is a

risk of re or explosions.

u Thoroughly remove all dust after sanding.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual may present a risk of

personal injury and/or damage to property.

Safety when sanding paint

Warning! Observe the applicable regulations

for sanding paint. Pay special attention to the

following:

u Whenever possible, use a vacuum extractor for dust col-

lection.

u Take special care when sanding paint which is possibly

lead based and may produce toxic dust:

u Do not let children or pregnant women enter the work

area.

u All persons entering the work area should wear a mask

specially designed for protection against lead paint dust

and fumes.

u Do not eat, drink or smoke in the work area.

u Dispose of dust particles and any other removal debris

safely.

Safety of others

u This appliance is not intended for use by persons (includ-

ing children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their

safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or ac-

cessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Additional safety instructions for batteries and

chargers

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not store in locations where the temperature may

exceed 40 °C.

u Charge only at ambient temperatures between 10 °C and

40 °C.

u Charge only using the charger provided with the tool.

u When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

Do not attempt to charge damaged batteries.

Chargers

u Use your BLACK+DECKER charger only to charge

the battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMCW210 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FMCW210 Manual

Product: