644328
2
Zoom out
Zoom in
Previous page
1/8
Next page
2
3
4 mono input channels and 2 stereo input channels.
Frequency EQ on each input channel.
Low-noise mic pre-amp on microphone inputs.
Low cut lter for the mono channel.
10dB attenuator switch on stereo channel.
One AUX output channel, one AUX input channel.
Individual stereo play input and record output channel.
Stereo monitor output and headphones output channel.
+48V phantom power for condenser microphones.
Balanced main outputs L+R
DSP effects processor, providing 16 kinds of effects.
USB interface enabling playback from a USB key source.
CONTROL PANEL
FEATURES
1. MIC. This is a balanced XLR type connector for
microphones. The input level ranges from -60 to -20dB. This
connector can provide +48V phantom power for condenser
microphones when the phantom power is switched on.
2. LINE This is a balanced 1/4” phone jack for linking a line
level source The input level ranges from -40 to 0dB.
3. GAIN Use this knob to adjust the level of the input signal
to the optimal level. For optimal S/N ratio and dynamic
range, adjust this knob so that the peak indicator lights up
occasionally.
4. LOW CUT Push down this switch to activate a low cut
lter, which allows high frequencies but attenuates low
frequencies.
5. HI This control determines the level of high frequencies in
the output signal.
6. MID This control determines the level of mid frequencies
in the output signal.
7. LOW This control determines the level of low frequencies
in the output signal.
8. EFF Use this knob to control the signal level sent from
each channel to the built-in effects processor. It is set after
the channel fader, so it is dependent on the fader position.
Adjust this knob when you use effects processor on this
channel.
9. AUX Use this knob to control the signal level sent from
each channel to the AUX bus. It is set before the channel
fader, so it is not dependent on the fader position.
10. PAN This control is used for distributing the signal level
of the channel feed to L / R buses. When the control is set to
12 o’clock, the signal is split evenly between L and R.
11. PEAK This LED signal will warn you of any excessively
high signal levels in the channel. The signal is sampled in
front of channel fader. It will light approximately 3dB before
clipping and therefore give warning of a possible overload.
12. LEVEL
This rotary fader controls the output level feed to the main
bus from the input channel.
MONO CHANNEL SECTION
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stagg S MIX 4M2S UD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stagg S MIX 4M2S UD in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info