584056
32
Zoom out
Zoom in
Previous page
1/33
Next page
XT375 / XT475 / XT675
31
Calibration procedure:
1) Remove the safety key
2) Press and hold down the Start and Fast (speed up) buttons with one hand and replace the safety key
with the other. Continue to hold the Start and Fast key until the window displays “Factory settings”,
then press the enter key.
3) You will now be able to set the display to show Metric or English settings. To do this press the up or
down key to show which you want, then press enter.
4) Make sure the wheel size diameter is 2.810 (2.98 for XT675) then press enter
5) Adjust the minimum speed (if needed) to 0.5 and then press enter
6) Adjust the maximum speed (if needed) to 12.0 and then press enter
7) Adjust the maximum elevation (if needed) to 15 and then press enter
8) Press start to begin calibration. The process is automatic, the speed will start up without warning so
do not stand on the belt.
Adjusting the speed sensor:
If the calibration does not pass you may need to check the speed sensor alignment.
1) Remove the motor cover hood by loosening the 4 screws that hold it in place (you do not need to
remove them completely).
2) The speed sensor is located on the left side of the frame, right next to the front roller pulley (the
pulley will have a belt around it that also goes to the motor). The speed sensor is small and black
with a wire connected to it.
3) Make sure the sensor is as close as possible to the pulley without touching it. You will see a magnet
on the face of the pulley; make sure the sensor is aligned with the magnet. There is a screw that
holds the sensor in place that needs to be loosened to adjust the sensor. Re-tighten the screw when
finished.
Maintenance menu:
1) Press and hold the Start, Stop and Enter key at the same time, until the display shows “Engineering
mode” (it may say maintenance menu, depending on version). Press the Enter key.
2) You can now scroll through the menu using the up and down keys. Use the Stop key to return to
previous menu selection. The menu selections are:
1) Calibration (used to verify calibration)
2) Factory settings (These should not be changed unless instructed by spirit service department)
3) Security (This allows you to lock the console keyboard)
4) Functions
i. Sleep (turns sleep mode on or off)
ii. Pause (turns pause mode on or off)
iii. Maintenance (reset lube message and odometer readings)
iv. Units (set display to English or Metric readings)
v. Grade return (returns the elevation to lowest setting when pause is pressed)
5) Display test (lights all LED lights for testing)
6) Key test (tests that all keys are functioning)
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit XT375 2007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XT375 2007 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info