552578

Speaka 527502 Manual

2
Zoom out
Zoom in
Previous page
1/4
Next page
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
Version 07/13
TV wall holder 65-105 cm
(26-42”) 35 kg
Item no. 52 75 02
Pay special attention to your safety when using electric tools (e.g. a drill). You should also heed
the safety instructions in the corresponding instructions.
Make sure no persons are in the area under the TV wall holder and/or the TV set during the instal-
lation.
Please observe the images on the attached sheet of these operating instructions.
Preparation of the TV set
• It is usually necessary to remove the TV set’s base before mounting it on a wall holder. Observe the operating
instructions for your TV set.
• Put the TV set fl at on a soft and clean underlay, the display side facing downwards. Do not apply pressure on the
display. Protect valuable furniture surfaces during installation by using a suitable pad or cloth.
• Remove the present base. Depending on the TV set, this base is either screwed tightly or clipped on.
Image 2
• Remove the two plastic covers (5) from the holder.
• Select the position and the height of the wall holder at the mounting location. In this process, the integrated water
level and the screw of the shaft must point upwards.
• Adjust the wall holder laterally using the integrated water level.
• Mark the necessary four drilling holes at the mounting site. To this end, use the wall holder as a template.
• Drill the required holes and insert suitable dowels in the boreholes (B or special dowels).
• Tighten the wall holder using suitable screws (A or screws matching the dowels) and washers (C).
• Replace the two plastic covers (5) onto the holder.
Image 3
Depending on the position of the attachment points on the TV’s back, there are different mounting options.
VESA up to 200x200
• The mounting plate can be mounted to the back of your TV set without using the extension brackets.
VESA up to 400x400
• The mounting plate is mounted to the back of your TV set using the extension brackets enclosed.
• Use the hexagon screws (D) of the screw set provided to fasten the extension brackets to the mounting plate.
Make absolutely certain the mounting plate is installed in the centre of the TV set.
Image 4
• Fasten the mounting plate on the back of your TV set using suitable screws (E-J) and washers (C or K), as shown
in the fi rst or second image.
• During the installation, keep in mind that the strap of the mounting plate must face towards the TV’s upper side.
When fi xing the mounting plate, make absolutely certain that you use the correct screws. Not
only must these be of the correct thread type for the TV set, but they must also not be too long;
otherwise they will damage the TV set.
The screws must not be too short, however, since otherwise the connection will not be secure.
The screws must be screwed into the threaded fi xture holes on the TV set with at least 5 full 360°
turns.
Should the screw length of the screws in the screw set provided not be suitable for your TV set,
please acquire suitable screws at your local hardware store.
If you have any doubt about the correct length of the screws required, we recommend that you
contact the TV manufacturer or an appropriate specialist.
• Do not use any force when tightening the screws; otherwise the TV set may be destroyed, leading to loss of war-
ranty/guarantee!
Image 5
• Lift the TV set with the mounting plate and place it onto the wall holder from the top, as shown in the fi rst image.
• The strap of the mounting plate must be inserted neatly into its counterpart on the wall holder.
• Secure the mounting plate on the wall holder using the two safety screws (M).
• Adjust the desired inclination angle using the lever screw connection. The lever can be pulled outwards in order to
be able to use it like a ratchet.
Maintenance and Care
The product does not have to be serviced and, except for occasional cleaning with a soft, dry cloth, requires no
maintenance whatsoever.
Never use aggressive cleaning agents or chemical solutions as these may damage the surface of the case.
Technical Data
TV size ................................... 65-105 cm (26-42”)
Load capacity ........................ max. 35 kg
VESA fi xture .......................... max. 400 x 400
Wall distance ......................... 65-480 mm
Material .................................. Steel/Aluminium
╞
OPERATING INSTRUCTIONS
Intended use
The TV wall holder is used for the mounting of suitable TV sets on walls.
The TV set may not exceed the values for TV size and weight specifi ed in the section “Technical Data”.
Any use other than that described above will lead to the damage of this product or of the TV set. Furthermore, this
involves risks such as damage to furniture in close proximity to the wall holder, personal injury etc.
No part of the product may be modifi ed or altered.
The safety instructions must be observed at all times.
Package content
See image 1 on the attached sheet of these operating instructions.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these safety
instructions. We do not assume any liability for any resulting damage.
We shall not accept liability for damage to property or personal injury caused by incorrect hand-
ling or non-compliance with the safety instructions. In such cases, the warranty will be null and
void.
The exclamation mark symbol indicates that important information is included in these operating
instructions.
The arrow symbol indicates tips and notes
• A TV wall holder is not a toy. Keep the device out of the reach of children.
• Do not leave packaging material lying around carelessly. It may become a dangerous plaything for children.
• Selecting an unsuitable installation location can lead to personal or material damage.
• Proceed with care when assembling and installing the product. The product may have sharp edges. There is a risk
of injury!
• Carry out only the work on the TV wall holder that is necessary in order to install it (or to adjust it). Never perform
any conversion or repair work.
• Before beginning the installation process, check whether there are appropriate mounting options for a TV wall holder
on the back of your TV set.
• Depending on the size and design of the TV set and TV wall holder concerned, it is sensible for a second person to
help with the installation. This person can hold the TV set still, for example, while you are attaching the TV set to the
wall holder.
• Apply your full concentration when carrying out the installation, because if the TV set and/or TV wall holder were to
fall, this could cause expensive damage to the equipment and there is the potential danger of personal injury!
• Lay all the TV set’s cables in such a way that they do not get jammed or kinked in the wall holder.
• Check all the screw fi ttings from time to time. Adjusting the position of the TV set and/or the wall holder and moving
them can sometimes cause the screws to become loose over time.
• Do not apply force when moving/adjusting the TV set or the TV wall holder. The TV set may get damaged from it.
• When moving/adjusting, do not press on the TV set’s screen.
• Do not overload the TV wall holder. Pay attention to the details provided by the manufacturer for the maximum TV
set weight and/or its size.
• Do not use the TV wall holder to support yourself or to hold onto.
• Do not fi x any objects to the TV wall holder other than the TV set for which it was intended.
• In case of doubt, do not perform the installation yourself. Have an expert carry out the installation.
Installation
Wall-mounting is permissible only where the wall concerned is of the correct type and condition.
Lightweight partition walls or those made from gypsum boards are normally unsuitable. However,
specialist retailers do sometimes stock special dowel fi ttings for such installation locations. If
you are in doubt, ask a specialist before installation.
Depending on the base wall material (e.g. concrete), suitable mounting materials must be used
(screws, dowels, etc.). The dowel screws enclosed are only suitable for solid walls. Special dow-
els and screws are not normally supplied with the TV wall holder and they must be bought sepa-
rately, depending on the type and condition of the wall concerned.
Due to the weight of the TV set, TV wall holder and the lever action involved, ensure that the
screws are fi xed securely.
Plan the installation location carefully, so that the TV wall holder with the TV set fi xed to it will be
situated at the correct location (height and position) when you have fi nished the installation.
Pay attention when drilling and tightening the screws that no cable or pipes in the wall are dam-
aged. Inadvertently drilling through electric cables causes the life-threatening danger of an elec-
tric shock!
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Speaka 527502 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Speaka 527502 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Speaka 527502

Speaka 527502 Installation Guide - English, German, Dutch, French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info