23388

Sony RMLG112 Manual

14
Zoom out
Zoom in
Previous page
1/16
Next page
masterpage:Left
filename[\\B-02w2000e\SONY RM-LG112\4247243111\424724311RMLG112U\GB04ADV_RM-
LG112-U.fm]
14
GB
model name1[RM-LG112]
[4-247-243-11(1)]
If the memory of the remote is already full,
the USE MODE button flashes 8 times in
quick succession and the remote
automatically exits the learning mode.
6 Repeat steps 1 through 5 to program
up to 10 IR codes.
Tip
If programming is unsuccessful, check the following:
– If the USE MODE button does not light up in step 1,
the batteries are weak. Replace both batteries.
– If the USE MODE button lights 4 times in quick
succession in step 3, an error has occurred. Start
again from step 1.
To cancel programming
Press USE MODE during any step. The remote
automatically exits the macro setting mode.
To delay the output of an IR code
Start over from step 1.
In step 3, press the easy scroll key lightly (for
less than 2 seconds). A 1 second delay is
programmed. The USE MODE button lights
twice slowly, then the remote automatically
exits the macro setting mode.
To clear the programmed IR
codes
Clear each macro step individually. In step 3,
press the easy scroll key for more than 2
seconds. The IR code is cleared. The USE
MODE button lights twice slowly, then the
remote automatically exits the macro setting
mode.
To start macro play
Move the easy scroll key to select “M1” or
“M2”, then press the key to enter the
selection
Note
If the Macro Play function does not work properly,
program a delay between each operation. See “To
delay the output of an IR code”.
You can switch the command mode (AV1 or
AV2) of the remote. If the command mode of the
receiver and the remote is different, you cannot
use the remote to operate the receiver.
1 Press ?/1 while holding down USE
MODE.
2 Move the easy scroll key to select
“MAIN”, then press the key to enter the
selection.
3 Move the easy scroll key to select
“AV1” or “AV2”, then press the key to
enter the selection.
The USE MODE button lights once (or
twice for AV2), then the command mode
switches.
To set the 2nd zone mode (North
American models only)
You can use the remote to select the input for the
2nd zone. You can use the easy scroll key only
for the 2nd zone.
1 Press ?/1 while holding down USE
MODE.
2 Move the easy scroll key to select
“2ND”, then press the key to enter the
selection.
The USE MODE button lights once, then
the command mode switches.
To reset the remote to factory
settings
Press ?/1, AV ?/1, and MASTER VOL – at
the same time. The USE MODE button lights 3
times, then goes off.
Selecting the mode of the
remote
… 14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony RMLG112 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony RMLG112 in the language / languages: English as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info