568042

Sonic Alert SBD375 Manual

2
Zoom out
Zoom in
Previous page
1/3
Next page
DUAL ALARM CLOCK WITH ADJUSTABLE TONE, VOLUME, AND
VIBRATOR
MODEL SBD375ss
OPERATION INSTRUCTIONS
IMPORTANT- Please read these instructions carefully before use and retain for future
reference.
Warning: To prevent fire or shock hazard do not expose this appliance to rain or moisture. Before
connecting to mains make sure that the requirements specified on the apparatus corresponds to the
available power supply i.e. USA: AC 110V / 60Hz EUROPE: AC 230V / 50 Hz.
Features shown on diagrams above:
1) Dual Alarm Setting 7) Slow Min/Hour Button 13) Alarm 1 (AL1) Indicator
Switch 8) Snooze Button 14) Alarm 2 (AL2) Indicator
2) Dimmer Switch 9) Time Set Switch 15) Vibrator/Bed Shaker Input
3) Clock Display 10) Tone Control Wheel 16) AC Power Input
4) PM Indicator (12 hr. only) 11) Function Switch 17) Backup Battery Compartment
5) Alarm SET/OFF Switch 12) Volume Control Wheel
6) Fast Min/Hour Button
GENERAL DATA
Power: Consumption: USA: AC 110V / 60Hz EUROPE: AC 230V / 50 Hz.
UL listed transformer (Underwriters Laboratories)
Setting the correct time-
1) Depress “TIME SET” button (9)
2)
As you depress the “TIME” button (9) at the same time depressing the “FAST” (6) or the “SLOW”
(7) minute/hour button to advance clock display until you have desired time.
3) Lighted dot (4) located in upper left corner o
f clock display indicates time is PM, no light indicates
time is AM.
Setting the alarm time-
1) To set alarm AL1 slide “DUAL ALARM SETTING SWITCH” (1) to AL1 position.
2)
Depress “ALARM SET/OFF” (5) button at the same time depressing “FAST” (6) or the “SLOW”
(7) minute/hour button until you reach desired alarm setting.
NOTE: when setting the alarm time if you advance more than 24 hours the display (3) will begin to
flash and alarm will sound. To stop flashing, move “FUNCTION SWITCH” (11) up then back to
OFF position. When alarm sounds display (3) will also flash.
3) Make sure alarm time is correctly set for AM or PM (4).
4)
Once alarm AL1 has been set, slide the “DUAL SETTING SWITCH” (1) to the AL2 position.
Follow the same steps that were taken when setting alarm AL1.
5)
Once both AL1 and AL2 have been set, slide the “DUAL SETTING SWITCH” to the middle
position AL1+AL2 for both alarms.
6)
You will see two dots on the right side of the LED display; AL1 (13) and AL2 (14) to show alarms
have been enabled. Lighted dots indicate which alarm is set.
Alarm-
1)
To enable the alarm function, slide the “FUNCTION SWITCH” (11) up to the position that you
desire to wake to, you can choose “VIB” for bed shaker, “BUZZ” for sound, and “VIB/BUZZ” for
both. NOTE: whichever function you choose to wake to, will be the same function for both alarms.
Snooze Operation-
1) “SNOOZE” button (8) – press after alarm has gone off. The alarm will re-
minutes for extra sleep. You may repeat up to 54 minutes.
2) When using “SNOOZE” (8) if alarm AL1 uses snooze, it will not affect alarm AL2.
Shutting Off Alarm-
Alarm can be shut off temporary for the day or permanently shut off.
1)
When alarm AL1 goes off, press the “ALARM SET/OFF” (5) button to turn off for the day.
2) Once both alarms go off and
the “ALARM SET/OFF” (5) button has been pressed, alarms will shut
off for the day and come back on the next day at the same time if alarm settings have not changed.
3)
To shut the alarm off permanently, slide the “FUNCTION SWITCH” (11) down to the OFF
positi
on. Alarm will not come on until “FUNCTION SWITCH” (11) is set to “VIB/BUZZ”, “VIB”,
or “BUZZ” position.
Volume Control-
1) To adjust volume, rotate wheel located on the lower right bottom corner of the clock (12).
Tone Control-
1) To adjust “TONE CONTROL” (10)
turn the wheel on the top right corner of the clock to the
desired tone sound.
Bed Shaker / Vibrator-
1) Attach the bed shaker jack to the back of clock at “VIBRATOR INPUT” (15).
2) To turn on vibrator slide “FUNCTION SWITCH” (11) to “VIB” or “VIB/BUZZ” position.
3) Place vibrator between mattress and box spring.
Battery Backup-
1) To use battery back up, install a 9-
volt alkaline battery in back of clock located under the
“BACKUP BATTERY COMPARTMENT COVER” (17). Battery not included. NOTE: the LED
display will not sh
ow during power failure, but the clock will still be running and keeping proper
time until the power comes back.AC_9V Power Input-
1) Attach the “AC POWER INPUT” (16) to the back of AC-
9V IN next to “VIBRATOR INPUT”
(15); it is the smaller input of the two.
Clock Format Switch-
Located on the back of the clock this switch is a 3 position switch to set the correct time format for your
country. The format is necessary for the clock to keep the correct time otherwise the clock may run too
fast or too slow.
NOTE:
IMPORTANT: do not confuse “AC POWER INPUT” (16) with the “VIBRATOR INPUT” (15).
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sonic Alert SBD375 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sonic Alert SBD375 in the language / languages: English as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sonic Alert SBD375

Sonic Alert SBD375 User Manual - German - 6 pages

Sonic Alert SBD375 User Manual - Dutch - 2 pages

Sonic Alert SBD375 User Manual - French - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info