Manual Sonic Alert HA360SSSC (page 1 of 2) (English)

771669

Zoom out

Zoom in

1/2

INSTALLATION AND SET UP FOR HOMEAWARE™ TRANSMITTER

HA360SSSC – Smoke / CO

The HomeAware™ Smoke/CO transmitter will alert you to the

sounds produced by the smoke and CO detectors already

installed in your home. This transmitter alerts you through the

HomeAware™ Main unit and remote receivers located in

other rooms.

Battery Backup Installation

Install a new 9 volt alkaline battery into the battery

compartment located on the back of the unit. See diagram for

battery door location. Battery backup will provide power

when a power outage has occurred. Power will be provided

for a continuous outage lasting 7 days, or for short outages

up to two years.

Link Button Set Up

This procedure will link your transmitter to your Main unit.

The Main unit will also provide an alert to all HomeAware™

remote receivers. When using the Bridge unit HA360BU all

original Sonic Alert receivers (SA101, SA201, BL300, and

SB1000) will also alert you.

It is best to do the link procedure in the same room with the

HomeAware™ Main unit, make sure the unit is plugged in.

To link a transmitter to your HomeAware™ Main unit:

1. Press set up button and the word LINK will be shown on

the display, press Enter. LINK will begin blinking.

(If LINK mode is entered by accident, simply press the

BACK button to exit and return to the clock.)

2. Press and hold down the Link button on the back of your

transmitter for about 1 second. The red LED on the

transmitter will light up. Release the button.

3. Upon successful connection, the red LED on the

transmitter will flash 2 times, then turn off. The

HomeAware™ main unit will briefly show DONE, and

return to the time display. Your transmitter is now

connected and ready to test and use.

Detecting the Different Alert Sounds

This transmitter detects loud sounds and will alert you to the

source of that sound.

When a sound is detected from the HA360SSSC it will send a

signal to the HomeAware™ base unit and all HomeAware™

remote receivers, also the red LED light will flash on the front

of the unit.

If this transmitter detects a loud sound from a smoke detector

that meets the T3 standard used for SMOKE DETECTORS,

“SMOKE” will scroll on the display of the HomeAware™ Main

Unit.

(The T3 standard is on for 0.5 sec, off for 0.5 sec, repeated 3

times, and followed by 1.5 sec of silence, as defined by NFPA

code 72.)

If the transmitter detects a loud sound from a CARBON

MONOXIDE (CO) DETECTOR that meets the T4 standard,

“CO” will scroll on the displayed of the HomeAware™ Main

Unit.

(The T4 standard is on for 0.1 sec, off for 0.1 sec, repeated 4

times, and followed by 5 sec silence, as defined by NFPA

code 720.)

For All Other Sounds

If a loud sound is detected that does NOT match the T3 or T4

standard, then “ALERT” will scroll on the HomeAware™ Main

unit in a loud, repeating pattern.

You can control the sensitivity level for the "ALERT" detection

using the switch on the back of the unit. There are three

levels to choose from: The HI setting is the most sensitive

setting and will alert you to more sounds. Moving this switch

to MED makes it less sensitive and will alert you to less

sound. The LO setting is the least sensitive. If you’re not

picking up the sound you need to be alerted to simply move

the sensitivity switch to a higher setting. If you have set this

setting to HI and you are still not picking up the sound, try

moving the transmitter closer to the sound.

Power Input

The HomeAware™ Smoke/CO transmitter uses an included

12V DC power adapter. Plug the power adapter into an 120V

AC power outlet, then plug the other end into the Low Voltage

12V DC input on the left side of the unit as show in the

diagram.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sonic Alert HA360SSSC in the language / languages: English as an attachment in your email.

The manual is 0.1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sonic Alert HA360SSSC Manual

Product: