771667
1
Zoom out
Zoom in
Previous page
1/2
Next page
INSTALLATION AND SET UP FOR HOMEAWARETRANSMITTER
HA360SSBC Baby Cry
The HomeAware™ HA360SSBC transmitter is
designed to alert you to the sound of a baby crying.
This transmitter alerts you through the HomeAware
Main unit and remote receivers located in other rooms.
Battery Backup Installation
Install a new 9 volt alkaline battery into the battery
compartment located on the back of the unit. See
diagram for battery door location. Battery backup will
provide power when a power outage has occurred.
Power will be provided for a continuous outage lasting
7 days, or for short outages up to two years.
Link Button Set Up
This procedure will link the HA360SSBC Baby Cry to
your Main unit. The Main unit will also provide an alert
to all HomeAware™ remote receivers. When using the
Bridge unit HA360BU all original Sonic Alert receivers
(SA101, SA201, BL300, and SB1000) will also alert
you.
It is best to do the link procedure in the same room with
the HomeAware™ Main unit, make sure the unit is
plugged in.
To link a transmitter to your HomeAware™ Main
unit:
1. Press set up button and the word LINK will be
shown on the display, press Enter. LINK will begin
blinking. (If LINK mode is entered by accident,
simply press the BACK button to exit and return to
the clock.)
2. Press and hold down the Link button on the back of
your transmitter for about 1 second. The red LED
on the transmitter will light up. Release the button.
3. Upon successful connection, the red LED on the
transmitter will flash 2 times, then turn off. The
HomeAware™ main unit will briefly show DONE,
and return to the time display. Your transmitter is
now connected and ready to test and use.
Sensitivity Switch
You can adjust the sensitivity of the Baby Cry detector.
There are three levels to choose from: The HI setting is
the most sensitive setting and will alert you to more
sounds. Moving this switch to MED makes it less
sensitive and will alert you to less sound. The LO
setting is the least sensitive. If you are not picking up
the sound you need to be alerted to, simply move the
sensitivity switch to a higher setting. If you have set this
setting to HI and you are still not picking up the sound
try moving the transmitter closer to the sound.
When a sound is detected it will send a signal to the
HomeAware™ base unit and all HomeAware™ remote
receivers, also the red LED light will flash on the front
of the unit.
Low Voltage Input
HomeAware™ transmitters have a low 120 volt AC
power supply that powers the HA360ss. Simply plug
the unit into any 120 volt AC power outlet. Next plug
the other end into the Low Voltage Input located on the
side, see diagram below.
FCC Requirements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions; (1)
This device might not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sonic Alert HA360SSBC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sonic Alert HA360SSBC in the language / languages: English as an attachment in your email.

The manual is 0.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info