474217
23
Zoom out
Zoom in
Previous page
1/27
Next page
Troubleshooting
22
Fault Check yes/no Possible cause Remedy
Gate does not fully open or
close.
Does gate stop before it has
reach its end position?
Have dimensions A/B been
remeasured?
no
yes
no
yes
yes
Wing hinge incorrectly
mounted
Change fittings at wing
Limit switch settings incorrect Readjust limit switch
Incorrect closing sequence Drive wires incorrectly con-
nected at terminals
Read the instructions and reconnect drives to the the
control system
Drive cannot be properly
programmed
DIL switch 8 is in position
OFF
End switch set incorrectly.
Set switch to position ON
Adjust end switch settings.
Gate is not stopped by an
obstacle
Gate is completing a pro-
gramming run
Force tolerance set too high
After the programming is completed, the force cut-off is
operational
Readjust force tolerance
Drive touches the post Incorrect dimension A or B Readjust connection of drive at the post
Limit switch settings incorrect Readjust limit switch
Irregular gate movement Incorrect dimensions A/B Adjust dimensions, if possible
Gate is stopped or contin-
ues in reverse motion.
Obstacle in operating
range?
Is gate wing hopping at
start?
no
yes
Hinges too stiff
Post has moved
Limit switch settings incorrect
Lubricate hinges
Contact specialist
Readjust limit switch
Force cut-off triggered Remove obstacle
yes Wing not stable Reinforce wing
yes Simply open and close gate again Wind pressure too highIs there strong wind?
Pedestrian wing cannot be
opened with remote control
device
Remote control key not pro-
grammed
Programme key, see section “Programming Remote
Control Devices”
Drive cannot be started Is LED “SH” flashing rap-
idly?
Position of jumper with pro-
grammed force values has
been changed
1. Reset jumper to previous position
2. Reset control system
3. Position jumper as desired
4. Complete programming runs
Gate cannot be
opened/closed with a key
switch.
LEDs “Power” + “Imp./Geh”
on?
no Cable connections loose
Key switch defective
Cable defective
Retighten terminals
Replace key switch
Replace cable
yes Pulser (key switch, remote
control) defective
Check pulser and replace, if defective.
Downloaded from www.Manualslib.com manuals search engine
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Twist 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Twist 200 in the language / languages: English as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Twist 200

Sommer Twist 200 User Manual - German - 29 pages

Sommer Twist 200 User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info