474217
25
Zoom out
Zoom in
Previous page
1/29
Next page
Störungssuche
24
Störungsart Kontrolle ja/nein mögliche Ursache Abhilfe
Tor läßt sich mit einem
angeschlossenen Schlüs-
seltaster nicht öffnen oder
schließen
LED “Netz + Imp./Geh”
leuchten
nein Kabelanschlüsse locker
Schlüsseltaster defekt
Kabelbruch
Klemmschraube nachziehen
Schlüsseltaster austauschen
Kabel erneuern
ja Impulsgeber (Schlüsseltaster,
Handsender) defekt
Impulsgeber überprüfen und bei Defekt austauschen.
Tor bleibt beim Öffnen oder
Schließen stehen und
reversiert
Hindernis im Bewegungs-
bereich
nein Scharniere schwergängig
Pfosten/Pfeiler hat sich ver-
ändert
Endschalter verstellt
Scharniere schmieren
Fachmann holen
Endschalter nachstellen
ja Kraftabschaltung ausgelöst Hindernis entfernen
Schwingt der Torflügel beim
Anlauf
ja Torflügel instabil Torflügel verstärken
Ging ein starker Wind ja Winddruck war zu stark Tor einfach noch mal öffnen und schließen
Tor öffnet oder schließt sich
nicht ganz
Tor hält vor der gewünsch-
ten Endlage
nein Torbeschlag falsch montiert Torbeschlag ändern
ja Endschalter falsch eingestellt Endschalter nachstellen
Schließfolge stimmt nicht Antriebe falsch angeklemmt Antriebe gemäß der Anleitung an die Steuerung
anschließen
Antrieb lernt die
Kraftwerte nicht ein
DIP-Schalter 8 in
Stellung OFF
Endschalter falsch einge-
stellt, Antrieb stoppt und
reversiert - Kraftabschaltung.
DIP-Schalter 8 auf ON stellen
Endschalter einstellen
Tor stoppt nicht bei einem
Hindernis
Tor in Lernfahrt
Krafttoleranz zu hoch
eingestellt
nach der Lernfahrt reagiert die Kraftabschaltung
Krafttoleranz reduzieren, siehe “Krafttoleranz einstel-
len”
Antrieb steht am Pfeiler an A- / B-Maße nachmessen nein A- oder B-Maß stimmt nicht Befestigung des Antriebes am Pfosten/Pfeiler
anpassen
ja Endschalter verstellt Endschalter nachstellen
Tor läuft ungleichmäßig ungleiche A- / B-Maße Maß ändern wenn es möglich ist
Gehtür öffnet sich mit dem
Handsender nicht
Handsendertaste nicht
eingelernt
Taste einlernen, siehe “Handsender einlernen”
Antriebe starten nicht LED “SH” blinkt schnell ja Jumper wurde mit
eingelernten Kraftwerten
umgesteckt
1. Jumper wieder auf vorherige Position stecken
2. Steuerungsreset durchführen
3. Jumper auf gewünschte Position stecken
4. Lernläufe durchführen
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Twist 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Twist 200 in the language / languages: German as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Twist 200

Sommer Twist 200 User Manual - English - 27 pages

Sommer Twist 200 User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info