655956
35
Zoom out
Zoom in
Previous page
1/160
Next page
Betriebs- und Wartungshinweise
DEUTSCH 34
x Bei stark abgebrannten Elektroden ist die Zündkerze sofort zu ersetzen – sonst nach
100 Betriebsstunden.
x Vorschriftsmäßiger Elektroden-Abstand: 0,5 mm.
Bei falschem Elektrodenabstand ist die Zündkerze zu ersetzen.
Folgende entstörte Zündkerzen sind für die Verwendung in diesem
Motorgerät zugelassen:
BOSCH WSR6F, CHAMPION RCJ-6Y und NGK BPMR7A
Die Verwendung anderer Zündkerzen ist nicht zulässig!
x Zündkabel (c) auf einwandfreien Anschluss und intakte Isolation prüfen. Bei beschädigter Isolation
nicht weiterarbeiten, sondern Reparatur bei einer von uns autorisierten Fachwerkstatt beauftragen.
x Zündkerze (d) wieder einschrauben. Drehmoment: 25 Nm
x Zündkerzenstecker (b) beim Wiederaufsetzen fest auf die Zündkerze (d) drücken
x Zündkerzen-Abdeckung (8) wieder montieren.
Verschmutzungsgefahr für Rippenband, zugehörige Trägerkonstruktion und Kupplung!
Rippenband-Abdeckung und Kupplungsabdeckung nur in sauberer Umgebung öffnen.
x Motor mit One-Touch-Stopptaster abstellen:
Î Kap. 6.2, Seite 24
x Wasserzufuhr zum Gerät abstellen.
x Motorgerät auf ebenen Untergrund stellen.
x Beide Befestigungsmuttern (a) der Rippenband-
Abdeckung (14) lockern.
x Rippenband-Spannschraube (13) linksherum
drehen, d. h. gegen den Uhrzeigersinn, um die
Rippenbandspannung zu verringern.
So lange drehen, bis die Vierkantmutter (b) so
weit es geht zur Markierung "" (c) hin bewegt
wurde. Bei Montage der Trennvorrichtung in
Mittelposition (vgl. Abbildung) befindet sich die
Vierkantmutter dann ganz links, bei Montage in
Außenposition ganz rechts.
x Beide Befestigungsmuttern (a) ganz
abschrauben.
x Rippenband-Abdeckung (14) abnehmen.
x Befestigungsmuttern (a) der Rippenband-
Abdeckung (14) wieder auf die zugehörigen
Schrauben drehen und nur leicht anziehen,
damit die Trennvorrichtung nicht herabfallen
kann.
x Alle 3 Befestigungsschrauben (d) der Kupplungs-
abdeckung (e) lösen. Die Schrauben müssen
nur so weit gelöst werden, bis sie sich ganz
leicht drehen lassen. Vollständiges
Herausdrehen der Schrauben ist nicht
erforderlich, da die Schrauben in der
Abdeckung verbleiben sollen.
x Ventilhebel (28) für Wasserzufuhr parallel zum
Anschlussstück legen, damit er beim folgenden
Arbeitsschritt nicht stört.
8.6 Rippenband wechseln
0,5 mm
14
b
a
13
c
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 879-12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 879-12 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info