380270
98
Zoom out
Zoom in
Previous page
1/100
Next page
74
E




Care and cleaning
Motor base
Wipe the motor base with a clean, damp cloth
after each use. Dry thoroughly with a soft, clean
cloth.
Processing bowl and lid
Hand wash in hot, soapy water using a mild
detergent. Do not use a scourer or abrasive
cleaners as they will scratch the plastic surface.
Lid seal
Your Breville ikonTM Food Processor is equipped
with a silicone seal, located in a recess around
the outer rim of the food processor bowl lid, to
reduce leakage while processing larger volumes
of wet ingredients. The silicon seal is removable
for cleaning purposes. However, to ensure its
effectiveness, the silicone seal must be inserted
correctly.
Removing the seal
Pry the silicone seal out of the recess in which it is
positioned, using your fingers or non marking, blunt
implement such as the tip of the plastic spatula
provided, and gently pull it over the lower edge of
the lid. Once a section of the silicon seal has cleared
the lower edge of the lid, it should come off with
ease. Be careful not to over-stretch the silicon seal
as this may damage or break it. Clean the silicon
seal in warm water using a mild detergent, rinse
and dry thoroughly.
Installing the seal
Step 1
To ensure the silicone seal is inserted properly, the
ribbed side of the seal should sit against the bowl
and the smooth side should face out.
Step 2
The smooth side of the seal has a thick and thin
section. Ensure the thin section of the seal is sitting
on top of the thick section. See diagram 1a
Step 3
Once positioned correctly, place a small section of
the silicon seal into the recess it was removed from,
then, holding the seal in position with one hand,
gently stretch the remainder of the seal over the lo-
wer edge of the lid and into the recess. Ensure that
the silicon seal aligns and sits wholly within the
recess around the outer rim of the food processor
bowl lid. See diagram 1
DIAGRAM 1:
SILICONE SEAL
DIAGRAM 1a:
SILICONE SEAL - DETAILED OF DIAGRAM 1
Quad
®
processing blade, dough blade,
discs and storage lids
Hand wash the bowl and lids. Use the double
ended cleaning brush accessory to scrub stubborn
food off blades and discs and for the inside of the
processing blade central support. To avoid acciden
-
tal cuts, do not leave Quad® processing blade or
discs to soak in sudsy water. The Quad
®
processing
blade, dough blade, discs and storage lids can also
be washed in the dishwasher (top shelf only).
Note
The small end of the double sided cleaning brush
can be used for cleaning small crevices of the
Quad
®
processing blade and dough blade shafts.
Anleitung_food_processor.indd 74 9.5.2008 11:19:47 Uhr
98


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solis typ 846 food processor 921 27 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solis typ 846 food processor 921 27 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info