24420
19
Zoom out
Zoom in
Previous page
1/21
Next page
39
11
The machine does not spin
The unbalanced load sensor has triggered because the washing is not
uniformly distributed inside the drum. If the washing is wet at the end of
the cycle, distribute it well inside the basket and repeat just the spin cycle.
12
Draining water from the
drum
In the event of a power failure or a fault in the appliance, the water inside
the drum can be drained as described in paragraph 6.3
13
The washing has not been
correctly spun
Large items have rolled up and are not uniformly distributed inside the
drum. Always wash large items together with small ones.
14
Residues of detergent on
the washing
Many phosphate-free detergents contain substances that are difficult to
dissolve in water.
Select the Rinse programme or brush the washing.
15
Washing results are unsat-
isfactory
- Too little detergent or an unsuitable detergent may have been
used.
- Stubborn stains were not pre-treated
- The wrong temperature was selected
- The drum was overloaded
ERROR SIGNALS
In the event of a malfunction, the “End” programme phase LED starts flashing and the LED's located above the
options buttons light up to signal the fault.
The “End” LED flashes for about half a second and then goes off for the same amount of time before flashing
again. While the “End” LED flashes, the LED's located above the options button flash but do so more rapidly. To
determine the type of error, count the number of times the “End” LED flashes:
Number of times the “End” programme
phase LED flashes between two 15 second
intervals
Problem
5
The tub does not fill with water
Consult the troubleshooting table at point: 2
6
The water does not drain from the tub
Consult the troubleshooting table at points: 4 and 5
1
A leak has occurred and aquastop has triggered (only for mod-
els fitted with this safety device)
For this type of error, turn off the water tap, remove the plug and
contact the Service Centre.
When the washing programme starts but the door has not been closed correctly, the “Start” and “Wash” pro-
gramme phase LED's start flashing alternatively at intervals of about half a second. This continues until the door
has been closed properly. The door open signal starts about 5 seconds after the washing programme com-
mences.
For all other error codes, contact the nearest Assistance Centre after disconnecting the power supply and closing
the water tap.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smeg STA120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smeg STA120 in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smeg STA120

Smeg STA120 User Manual - Dutch - 24 pages

Smeg STA120 User Manual - French - 22 pages

Smeg STA120 User Manual - Italian - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info