Manual Smeg se 2663 tc1 (page 9 of 15) (English)

335582

Zoom out

Zoom in

1/15

Instructions for the user

7.2.8 Timer (on some models only)

Some models are equipped with a 1 to 99-minute cooking timer.

To use the timed cooking, first set the power level by following the instructions given in paragraphs

“7.2.2 Single Cooking Zones” and “7.2.3 Dual Cooking Zones”.

Now, with the hob NOT locked out (if it is locked out, press the

key to enable the functions), press

the symbol

Between the symbols

and of the first active cooking zone, a LED light will turn on to indicate that

the minutes to be set will refer to operation of that particular zone.

The automatic operation minutes of the cooking zone can be increased or decreased by using the

and

keys beside .

After 5 seconds have gone by since the last time it is pressed, the timer will start and the cooking zone

will operate until the display above the symbol

reaches 0.

At this point the cooking zone will automatically turn off.

It is also possible to use the timed cooking function on more than cooking zone at the same time.

Once the timer is set on the first zone, press

key to shift the timer controls over to the next active

zone (the LED light between the symbols

and of the second active cooking zone will be

activated) and then set the cooking duration as previously described.

When the timed cooking is active on several cooking zones at the same time, the display between the

symbols

and of the cooking zone will alternatively turn on and at the same time the minutes

display found on the symbol

will show the time remaining for the zone with the LED light on.

7.2.9 Modifying the data set

During timed cooking, each single pressure on the

and symbols increases or reduces the power

of the cooking zone.

To change the remaining time of a zone, you have to press

key until the LED light in the cooking

zone turns on. Now it will be possible to change the operating time by working with the symbols

and

of the timer.

7.2.10 Residual heat

Each cooking zone is equipped with a residual heat warning device. After any zone is switched off, a

flashing “

”may appear on the display. This warns that the cooking zone concerned is still very hot.

Cooking can be restarted while the

is flashing; proceed as described in points “7.2.2 / 7.2.3”.

7.2.11 Control circuit board thermal protection

If the cooking zones cause overheating of the internal electronic circuit board, the heat will be switched

off automatically. This switches off power to the front zones, and the letters

and flash alternately

on the power leds. If the circuit board does not cool down, power to all the cooking zones is switched

off, and the power leds display the text

. Cooking can be resumed once the temperature

has dropped below the safety threshold.

7.2.12 Operator Error

If the user makes a mistake when using the push-buttons, an

appears on the power display; it will

remain there as long as the user continues to press the button being used incorrectly.

7.2.13 Switching off the cooking zones

The cooking zones are switched off when the operational power display indicates 0. The zone will

automatically deactivate 5 seconds after the display shows 0.

If the cooking zones are hot, the blinking residual heat “

” will appear after they are switched off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Smeg se 2663 tc1 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smeg se 2663 tc1

Smeg se 2663 tc1 User Manual - German - 16 pages

Smeg se 2663 tc1 User Manual - Dutch - 15 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Smeg se 2663 tc1 Manual

Product: