603162
1
Zoom out
Zoom in
Previous page
1/10
Next page
INSTALLATION AND OPERATING INSTRUCTIONS
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT
TO INSTALL OR OPERATE
Model: 3002
INTRODUCTION
This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas
heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio
frequencies (RF) within a 20-foot range using non-directional signals. The system operates one of 1,048,576 security codes that are
programmed into the transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.
Review COMMUNICATION SAFETY under theTRANSMITTER SECTION and THERMO SAFETY under the REMOTE RECEIVER
SECTION. These signal/temperature safety features shut down the appliance when a potentially unsafe condition exists.
REV. 4-19-12 Page 1
Skytech: 3002
The transmitter operates on (2) AAA-size 1.5V batteries. It is recommended that ALKALINE batteries always be used for
longer battery life and maximum operational performance. IMPORTANT: New or fully charged batteries are essential for
proper operation of the multi-function transmitter. Insert (2) AAA-size 1.5 V batteries into the battery compartment on the
back of the transmitter, positioning the (+) and (-) ends of the batteries as indicated on the casing. When the batteries are
inserted, gure #2 (with similar numbers) will display.
Fig. 1 Transmitter Front and Back Views
Note: If a LOW battery icon appears on the screen,
check the position of the batteries.
CAUTION: Due to the sensitive temperature-monitoring
components in the transmitter, it may be necessary to
allow the transmitter to stabilize to room temperature
before accurate room temperatures are displayed on
the screen. If the transmitter is activated from a
severe cold condition, it can take up to fteen minutes
for accurate temperature readings to appear.
1. BATTERY ICON - Symbol means battery power is low. Replace batteries within 2-weeks.
2. TIMER- Indicates time remaining before system shuts OFF, when timer-programmed; 9-hour maximum setting.
3. MODE- Indicates operation MODE of system. ON indicates the system is manually ON. OFF indicates the entire
system is turned OFF and THERMO indicates the system will automatically cycle ON/OFF, depending on the SET
temperature.
4. SET- Indicates desire SET room temperature for THERMO operation.
5. FLAME – Indicates burner/valve in ON position.
6. CLOCK – Indicates the current time in AM/PM
7. ROOM – Indicates CURRENT room temperature.
8. °F indicates degrees Fahrenheit (°C indicates degrees Celsius).
LCD DISPLAY FUNCTIONS
ROOM
SET
1
2
3
4
5
6
7
8
Fig. 2 LCD Display Functions
MODE
COVER CLOSED
MODE
TIMER
TIME
SET
SLIDE COVER
OPEN
+
+
-
-
AAA
BACK OF
TRANSMITTER
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skytech 3002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skytech 3002 in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info