536967
2
Zoom out
Zoom in
Previous page
1/2
Next page
BATTERYWARRANTY
If, within one year from date
of purchase, this product
should become defective
(except battery), due to
faulty workmanship or
materials, it will be repaired
or replaced, without charge.
Proof of purchase is
required.
12 volt " cigarette lighter "
type (size 23A) battery
(included).
2d. If your existing transmitter or receiver has fewer than 12 switches, match only the first corres-
ponding connectors. Leave the remaining posts blank, (remove the connectors).
2e. If your existing opener does not have any switches, then it can “learn”
the code needed to open your garage door. Set the connectors of the
model 68 to any combination of “ +, 0 , - ”. For security reasons, do not
leave the connectors at the current position (see point 2c on how to move
the connectors). Press the learn button on the garage door opener (unit
with motor located in the ceiling of the garage, see diagram J) for appro-
ximately two seconds. The LED light located beside the learn button will
go on. Then press the button on the model 68 transmitter and hold for
about one second. The LED light on the garage door opener will flash
then go off.
The model 68 is now pro-
grammed correctly and will
open your garage door.
Diagram J
‘Learn’ Button
Garage Door
Opener (GDO)
STEP 2 - SET CODE CONNECTORS
®
Skylink will not be held
liable or responsible for
any misuse or application
of this product other than
for its intended use.
GARAGE DOOR/GATE
REMOTE CONTROL
USER'S INSTRUCTIONS
(Model 68)
® are registered trademarks of their respective corporations
CUSTOMER SERVICE
2213 Dunwin Drive
Mississauga, Ontario,
L5L 1X1, CANADÁ
(905)608-9223
(905)608-8744 FAX
Email:support@skylinkhome.com
(Reply within 24 hrs)
Customer Service : (800)304-1187
From Monday to Friday, 9am to 5pm EST
http://www.skylinkhome.com
P/N. 101A184-001 Rev.1
Patent no. D380895, 5680134,
5841390, 6005508
Patents Pending
©2002 SKYLINK GROUP
Diagram I
If your garage door opener is manufactured by (Chamberlain
®
, Sears
®
, Lift-Master
®
, Wayne Dalton
®
, Pulsar
®
or Master
Mechanic
®
) the switches will have 3 positions, (“+, 0, -”). Set the connectors on the model 68 to match their corresponding
positions.
If your opener is a Sears
®
, Chamberlain
®
or Lift-Master
®
and the existing transmitter has three buttons, (see diagram I), the first
connector in the model #68 may need to be changed to another position.
If your Chamberlain
®
, Sears
®
, Lift-Master
®
has 9 DIP switches, match them to the first 9 connectors on the model 68 and
remove the last 3 connectors (connectors 10, 11, 12). If there are only 8 DIP switches on your Chamberlain
®
,Sears
®
, Lift-
Master
®
, match them to the 2-9 position on the model 68 and remove the last 3 connectors
(connectors 10, 11, 12). Now you may have to change the positioning of the #1 connector
on the model 68.
If the large button of Diagram I is used to open the garage door, set the #1 connector to “ - ”
position. If the middle button is used, set the #1 connector to the “ 0 ” or “blank” position. If
the smaller button on the left is used, set the #1 connector to the “ + ” position.
Diagram H
Original Position
Reversed Position
If your existing transmitter has fewer
than 12 switches, see point 2d in this
manual. Press the button on the trans-
mitter. If the garage door does not open,
reverse all of the connectors on the
model 68. The “ + ” will be changed to
the “ - ” position and the “ - ” position
will be changed to the “ + ” position.
(see diagram H)
FCC
The Universal Garage Door Remote Control
is approved by the FCC and it complies with
Part 15 of the FCC Rules. Its operation is
subject to the following two conditions :
1. This device may not cause harmful inter-
ference.
2. This device must accept any interference
that may cause undesired operation.
WARNING:
Changes or modifications to this unit not
expressly approved by the party responsible
of compliance could void the user’s authority
to operate the equipment.
WARNING
If this transmitter triggers
other garage doors in
your neighborhood,
change all your trans-
mitters and receiver to a
new code setting.
DO NOT let children use
the garage door trans-
mitter without adult
supervision. Children
can injure themselves or
others by the garage
door.
NOTE
If your Skylink Universal Remote Control does not activate
your Garage Door Opener, the reason may be that your
GDO age or manufacturer is not listed on the compatibility
chart.
The solution is the Skylink UR-100 Universal Receiver.
If you would like to order Skylink’s product or have difficulty
getting your Skylink’s remote control to work, please :
1. visit our website FAQ at
www.skylinkhome.com, or
2. email us at support@skylinkhome.com
(reply within 24 hrs)
3. call our toll free at 1-800-304-1187 from Monday to Friday,
9 am to 5 pm EST.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skylink 68 - remote at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skylink 68 - remote in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info