591198
5
Zoom out
Zoom in
Previous page
1/96
Next page
5
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
dierent from those intended could result in a hazardous
situation.
5) SERVICE
a) 
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR SANDERS
GENERAL
 This tool should not be used by people under the age
of 16 years
 This tool is not suitable for wet sanding
 Never use the tool when cord is damaged; have it
replaced by a qualied person
 Do not work materials containing asbestos
(asbestos is considered carcinogenic)
 Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
 SKIL can assure awless functioning of the tool only
when original accessories are used
 Do not continue to use worn, torn or heavily clogged
sanding sheets
BEFORE USE
 Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
 Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
 Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
 The noise level when working can exceed 85 dB(A);
wear ear protection
 Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
 Certain kinds of dust are classied as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
 Follow the dust-related national requirements for the
materials you want to work with
 Wear protective gloves, safety glasses, close-tting
clothes and hair protection (for long hair)
 Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
 When sanding metal, sparks are generated; do not
use dustbag and keep other persons and combustible
material from work area
DURING USE
 Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
 Do not touch the moving sanding disc
 In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
 If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
 When you put away the tool, switch o the motor and
ensure that all moving parts have come to a complete
standstill
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
 Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
 If for any reason the old plug is cut o the cord of
this tool, it must be disposed of safely and not left
unattended
USE
 Backing pads
- never run the tool without backing pad A
! replace damaged backing pads immediately
(loosen/fasten 4 pad screws B)
! unplug tool before removing/mounting backing
pads
 Mounting of sanding sheet
- mount VELCRO sanding sheet as illustrated
- if necessary, clean backing pad rst
! perforation in sanding sheet should correspond
with perforation in sanding foot
! the dust suction requires the use of perforated
sanding sheets
! replace worn sanding sheets in time
 Dust suction
For optimal dust pick-up performance
- mount dustbag D
- empty dustbag regularly
! do not use dustbag when sanding metal
 On/o
- before switching on the tool, you should place it with
the entire sanding surface on the workpiece
- when switching on, do not apply too much pressure
on the tool
- switch on/o the tool by pushing switch E in "I"/"O"
position
! be aware of the sudden impact when the tool is
switched on
! 
from the workpiece
 Holding and guiding the tool
! 
coloured grip area(s)
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- guide the tool parallel to the working surface and move
it in circles or in a cross pattern
- do not tilt the tool in order to avoid deep unwanted
sanding marks
- keep ventilation slots F uncovered
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 7420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 7420 in the language / languages: All languages as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info