389821
4
Zoom out
Zoom in
Previous page
1/40
Next page
INTRODUCTION
This tool is intended for dry sanding and finishing of
wood, painted surfaces, plastic and filler
TECHNICAL SPECIFICATIONS 1
SAFETY
Read and save this instruction manual (pay special
attention to the safety instructions at the back)
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Always keep the cord away from moving parts of the tool
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
SKIL can assure flawless functioning of the tool only
when original accessories are used
This tool should not be used by people under the age of
16 years
The noise level when working can exceed 85 dB(A);
wear ear protection
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
Never use tool when cord is damaged; have it replaced
by a qualified person
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
This tool is not suitable for wet sanding
Do not sand material containing asbestos
When sanding metal, sparks are generated; do not use
dustbag/vacuum cleaner and keep other persons and
combustible material from work area
Do not touch the moving sanding sheet
Do not continue to use worn, torn or heavily clogged
sanding sheets
Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
Wear a dust protection mask when working with
materials which produce dust that is detrimental to
health; inform yourself beforehand about the materials to
be worked on
Always direct the cord to the rear away from the tool
Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
Mounting of sanding sheet
7310/7320 2a
7330/7340/7345 2a+b
! the dust suction requires the use of perforated
sanding sheets
- perforation in sanding sheet should correspond with
perforation in sanding foot
! replace worn sanding sheets in time
Dust suction
7310 3
- when using tool with/without vacuum cleaner, mount
vacuum cleaner adaptor A as illustrated
! do not use vacuum cleaner when sanding metal
7320/7330/7340/7345 4
- mount dust bag
- empty dustbag regularly for optimal dust pick-up
performance
! do not use dustbag when sanding metal
On/off switch
- switch on/off the tool by pushing switch B 3 forward/
backwards
! before the sanding surface reaches the
workpiece, you should switch on the tool
! before switching off the tool, you should lift it
from the workpiece
VariTronic speed control (7340/7345)
For optimal sanding results on different materials
- with wheel C 4 you can set the desired sanding
speed
- adjust speed to grit size used (see: Application
Advice)
- before starting a job, find the optimal speed and grit
by testing out on spare material
Holding and guiding the tool 5
- guide the tool parallel to the working surface
! do not apply pressure on the tool; let the sanding
surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
-keep the ventilation slots uncovered
APPLICATION ADVICE
Move the tool in straight movements in line with the
grain
- for sanding bare wood surfaces
- for extra fine finishing
Never use the same sanding sheet for wood and metal
Recommended sanding sheet grits:
coarse - for removing paint;
for sanding of extremely rough wood
medium - for sanding of rough or plain wood
fine - for smoothing of wood;
for finishing of bare wood;
for smoothing surfaces with old paint
Use different grit sizes when the working surface is
rough:
- start sanding with coarse or medium grit
- finish with fine grit
For more tips see www.skileurope.com
GB
4
SKIL7310/20/30/40/45.qxd 05-02-2004 09:56 Pagina 4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 7340 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 7340 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info