Manual Skil 4375 (page 5 of 48) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

383155

Zoom out

Zoom in

1/48

INTRODUCTION

● This tool is intended for making cut-throughs and

cut-outs in wood, plastic, metal, ceramic plates and

rubber, and is suitable for straight and curved cuts with

mitre angles to 45°

TECHNICAL SPECIFICATIONS 1

SAFETY

● Read and save this instruction manual (pay special

attention to the safety instructions at the back)

● Always keep the cord away from moving parts of the tool

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Do not cut material containing asbestos

● Do not use a saw blade which is cracked, deformed or

dull

● Keep hands away from the saw blade while the tool is in

use

● Remove all obstacles on top of as well as underneath

the cutting path before you start cutting

● Always disconnect plug from power source before

making any adjustment or changing any accessory

● Wear a dust protection mask when working with

materials which produce dust that is detrimental to

health; inform yourself beforehand about the materials to

be worked on

● Wear protective goggles when working with materials

which produce chips

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start cutting

● Check the functioning of the tool before each use and, in

case of a defect, have it repaired immediately by a

qualified person; never open the tool yourself

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● When used outdours, connect the tool via a fault current

(FI) circuit breaker with a triggering current of 30 mA

maximum, and only use an extension cord which is

intended for outdour use and equipped with a

splashproof coupling-socket

● The noise level when working can exceed 85 dB(A);

wear ear protection

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● This tool should not be used by people under the age of

16 years

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left

unattended

USE

● On/off

Switch on/off the tool by pulling/releasing trigger A 2

● Switch lock

- pull trigger A 2 and hold it while you press knob B 2

- release the trigger

- unlock the switch by pulling again trigger A and then

releasing it

● Speed control (4330/4374/4375)

Select speed with speed selection wheel C 2 (the

selfcorrecting VariTronic-Extra system keeps the speed

practically constant as the load increases)

● Recommended speed (4330/4374/4375) 3

● Recommended orbital action (4374/4375) 4

! when sawing splinter-sensitive material, use

lower orbital settings, or switch off orbital action,

to avoid splintering

● Vari-Orbit system (4374/4375)

- use knob D 2 for adjusting the orbital action from

accurate cutting (=0) to fast cutting (=Full)

! Vari-Orbit system is activated when saw blade

enters into the workpiece

● Dust suction

Prevents large accumulations of dust, high dust

concentrations in the breathing air and facilitates the

disposal of saw dust

- mount vacuum cleaner adapter 5

- connect vacuum cleaner

- clean vacuum cleaner adapter regularly

! do not use vacuum cleaner when cutting metal

● Contact protector

Contact protector G 2 prevents unintentional contact

with the saw blade while working

● Changing blades 6

For mounting:

- turn knob E counter-clockwise and hold it in this

position

- insert blade to full depth with teeth facing forward

- release knob E

For removing:

- turn knob E counter-clockwise and hold it in this

position

- turn blade slightly to the right and pull it out

- release knob E

● Adjusting bevel cutting angle 7

- loosen screw H

- adjust footplate F to required angle

- tighten screw H

XP SKIL 4230/4330/4374/4375 28-05-2002 12:44 Pagina 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 4375 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 4375 Manual

Product: