389827
5
Zoom out
Zoom in
Previous page
1/8
Next page
VariTronic speed control (1205) 7
- select belt speed with speed selection wheel H
- information on belt speed setting can be obtained
from the sticker positioned on the front end of the tool
Holding and guiding the tool 8
- guide the tool parallel to the working surface
! do not apply pressure on the tool; let the sanding
surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep the ventilation slots uncovered
APPLICATION ADVICE
For sanding bare wood surfaces move the tool in
straight movements in line with the grain
For sanding all other surfaces move the tool in oval
movements over the material
For stationary use put clamps (SKIL accessory
2610373265) in holes in tool housing and tighten them
to the workbench 9
For sanding large surfaces always use the sanding
frame in order to avoid an uneven surface
Never use the same sanding belt for wood and metal
Recommended sanding sheet grits:
coarse - for removing paint;
for sanding of extremely rough wood
medium - for sanding of rough or plain wood
fine - for smoothing of wood;
for finishing of bare wood;
for smoothing surfaces with old paint
Use different grit sizes when the working surface is rough:
- start sanding with coarse or medium grit
- finish with fine grit
For more tips see www.skileurope.com
GUARANTEE / ENVIRONMENT
Always keep tool and cord clean (especially the
ventilation slots)
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
Dispose of the tool by sorting tool, accessories and
packaging for environment-friendly recycling (the plastic
components are labeled for categorized recycling)
INTRODUCTION
Cet outil est conçu pour le ponçage à sec avec une
grande capacité à enlever la matière du bois, plastique,
métal et mastic et des surfaces peintes
SPECIFICATIONS TECHNIQUES 1
SECURITE
Lire et conserver ce manuel d'instruction (faire en
particulier très attention aux instructions de sécurité au
dos de ce manuel)
Faites attention aux vis, clous ou autres éléments qui
pourraient se trouver dans la pièce à travailler et qui
risqueraient d’endommager très fortement votre outil;
d'abord les enlever puis travailler
Garder toujours le câble éloigné des parties mobiles de
votre outil
Lorsque vous rangez votre outil, le moteur doit être
coupé et les pièces mobiles complètement arrêtées
Utiliser un câble de prolongement complètement déroulé
et de bonne qualité d'une capacité de 16 A
En cas d’anomalie électrique ou mécanique, couper
immédiatement l’outil et débrancher la prise
SKIL ne peut se porter garant du bon fonctionnement de
cet outil que s’il a été utilisé avec les accessoires
d’origine
Cet outil ne doit pas être utilisé par des personnes en
dessous de 16 ans
Le niveau sonore en fonctionnement peut dépasser
85 dB(A); munissez-vous de casques anti-bruit
Si le câble est endommagé ou rompu pendant le travail,
ne pas y toucher, mais immédiatement débrancher la
prise
N'utiliser jamais d'outil avec un câble endommagé;
faites-le remplacer par un technicien qualifié
Toujours contrôler si la tension secteur correspond à la
tension indiquée sur la plaquette signalétique de l’outil
(les outils conçus pour une tension de 230V ou 240V
peuvent également être branchés sur 220V)
Cet outil ne convient pas pour des surfaces à poncer
imperméabilisées
Ne pas poncer des matériaux composés d'amiante
Lorsque vous poncez du métal, des étincelles se
produiront; ne pas utiliser le sac à poussière et tener
toute autre personne ou tout matériel combustible
éloignés de votre domaine de travail
Ne toucher pas la bande de ponçage en rotation
Ne plus utiliser les bandes de ponçage usées, fissurées
ou fortement encrassées
Porter des gants de protection, des lunettes de
protection, des vêtements près du corps et un protège
cheveux (pour des cheveux longs)
Porter un masque de protection lors de travaux sur des
matériaux produisant des poussières nuisibles à la
santé; toujours s’informer de la technicité de ces
matériaux avant de travailler avec ceux-ci
Toujours ramener le câble vers l'arrière, à l'abri de l'outil
Toujours débrancher l’outil avec tout réglage ou
changement d’accessoire
UTILISATION
Montage du cadre de ponçage 2
- tourner la ponceuse à l’envers avec le cable tourné
vers vous
- pousser le bouton A vers le haut
F
6
XP SKIL 1200/1205 28-05-2002 11:54 Pagina 6
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 1200 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Skil 1200

Skil 1200 User Manual - English, German - 48 pages

Skil 1200 User Manual - German - 8 pages

Skil 1200 User Manual - Dutch - 48 pages

Skil 1200 User Manual - Dutch - 9 pages

Skil 1200 User Manual - Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian - 48 pages

Skil 1200 User Manual - Norwegian - 9 pages

Skil 1200 User Manual - Finnish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info