Manual Skandia 1088024 - Digitale Multimeter (page 2 of 2) (English, Dutch)

681540

Zoom out

Zoom in

1/2

Skandia Digital Multimeter 1088024





This multimeter has been designed according to IEC-61010

concerning electronic measuring instruments with an overvoltage

category (CAT III 600V) and pollution 2.

Only to use for measurements in a 1-phase electrical 600V

installation after the group distribution frame.!!!

Also to use for measurements of electric appliances with a plug

and lighting connected on this installation after the group

distribution frame.!!!



maximum 600Voltage.



meter is used safely and is kept in good ope g condition.



test leads supplied. If necessary, they must be replaced with the

type speciﬁed in this manual.



Important safety information, refer to the operating manual.

Dangerous voltage may be present.

Earth ground.

Double insulation (Protection class II).

 Over voltage category II for measurments on electric and

electronic appliances who by way of a plug is provided of

voltage. This catagory enclosed also all smaller catagory’s (for

instance CAT I for measuring of signal and steering tension.









  when a higher degree of reliabilty

and availability is desired.





 Before opening the case, always disconnect test leads from

all energized circuits

 

the speciﬁed voltage and current ratings:

 

 

fastened completely.

 

To clean it using a damp cloth and mild detergent only.





speciﬁcations for each range of measurement.



unused terminals.



60V above earth ground in category III installations.



set the range selector at the highest position.



disconnect test leads from the circuit under test.



circuits always remember that there may be high amplitude

voltages pulses at test points, which can damage the meter.



30V AC rms. Keep ﬁngers behind the probe barriers while

measuring.

 







Continuity Test with battery operated.







1. Display

 

2. Back light (option)

 

 

again, just push this button once.



This switch is used to select functions and desired ranges as well

 

4. Hold button

 

 



Plug in connector for red test lead for 10A measurement.

6. “COM” jack

Plug in connector for black (negative) test lead.

ΩmA” jack

Plug in connector for red (positive) test lead for voltage,

resistance and current (except 10A) measurements.



Accuracy is speciﬁed for a period of one year after calibration and





Maximum voltage between : CAT III 600V

terminals and earth ground

 

 

 

  

 

converter

Overrange Indication : Only ﬁgure “1” on the display

Polarity indication :“-”displayed for negative polarity

Operating Environment :0 to 40°C

 

  “appears on the display

 

 



  

  

  

  

  

600V 1V ±0.8% of rdg ± 2 digits



rms. AC for other ranges.



  

20μA 0.01μA ±1% of rdg ± 2 digits

2mA 1μA ±1% of rdg ± 2 digits

20mA 10μA ±1% of rdg ± 2 digits

  

10A 10mA ±3% of rdg ± 2 digits





  

200V 100mV ±1.2 % of rdg ± 10 digits

600V 1V ±1.2 % of rdg ± 10 digits

Overload Protection: 600V DC or rms. AC for all ranges.



calibrated in rms. of a sine wave.



 

 Ω),

built-in buzzer will sound.

 

the diode.

DC or rms. AC.



  

200Ω 0.1Ω ±0.8% of rdg ± 3 digits

2kΩ 1Ω ±0.8% of rdg ± 2 digits

20kΩ 10Ω ±0.8% of rdg ± 2 digits

200kΩ 100Ω ±0.8% of rdg ± 2 digits

2MΩ 1kΩ ±1.0% of rdg ± 2 digits

Maximum Open Circuit Voltage: 3.2V

DC or rms. AC for all ranges





1. Connect the red test lead to the “V.Ω.mA” jack and the black

lead to the “COM” jack.



measured is not known beforehand, set range switch at the

highest range position and then reduce it until satisfactory

resolution is obtained.

3. Connect test leads across the source or load being measured.



the red lead connection



1. Connect the red test lead to the “V.Ω.mA” jack and the black

 

and 10A, remove red lead to“10A” jack.)



3. Open the circuit in which the current is to be measured, and

connect test leads in series with the circuit.



lead connection.



1. Connect the red test lead to “V.Ω. mA” jack and the black test

lead to the “COM” jack.



3. Connect test leads across the source or load being measured.





1. Connect the red test lead to “V. Ω. mA” jack and black test lead

to the “COM” jack. (The polarity of red lead is positive “+”.)

 Ω” range position.

2. Connect test leads across the resistor to be measured and read



4. If the resistance being measured is connected to a circuit, turn off

power and discharge all capacitors before applying test probes.



1. Connect the red test lead to “V.Ω.mA” jack and the black test

lead to the “COM” jack. (The polarity of red lead is positive “+”.).

 position.

3. Connect the red test lead to the anode of the diode to be tested

and the black test lead to the cathode of the diode.

4. The approx. forward voltage drop of the diode will be displayed.

If the connection is reversed only ﬁgure “1” will be shown.



1. Connect red test lead to “V.Ω.mA”, black test lead to “COM”.

 ” position.

3. Connect test leads to two points of circuit to be tested.

If continuity exists, built-in buzzer will sound.



If “

”appears on display, it indicates that the battery should be

replaced.



operator’s error.





replace with a new one.

Be careful to observe battery polarity.



Before attempting to open the case, always be sure that test leads

have been disconnected from measurement circuits. Close case and

tighten screws completely before using the meter to avoid electrical

shock hazard.



















 

Skandia



















Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skandia 1088024 - Digitale Multimeter in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Skandia 1088024 - Digitale Multimeter

Skandia 1088024 - Digitale Multimeter User Manual - Dutch - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skandia 1088024 - Digitale Multimeter Manual

Product: