616801
94
Zoom out
Zoom in
Previous page
1/96
Next page
92
GENERAL PROBLEMS
0DFKLQHGRHVQRWVHZ
* Power switch is turned off.
-
Turn on the switch.
* Buttonhole lever is not raised when sewing stitch patterns.
– Raise buttonhole lever.
* Buttonhole lever is not lowered when sewing buttonhole.
– Lower buttonhole lever.
* Bobbin winder is engaged. – Disengage bobbin winder (see
page 16 - 17).
0DFKLQHMDPVNQRFNV
* Thread is caught in hook.
-
Clean hook (see page 68 - 69).
* Needle is damaged.
-
Replace needle (see page 26 - 27).
Fabric does not move.
* Presser foot is not lowered
-
Lower presser foot.
* Stitch length is too short - Lengthen stitch length.
STITCHING PROBLEMS
0DFKLQHVNLSVVWLWFKHV
* Needle is not all the way up into needle clamp (see page
26 - 27).
* Needle is bent or blunt.
-
Replace needle (see page
26 - 27).
0DFKLQHLVQRWWKUHDGHGFRUUHFWO\VHHSDJH
* Thread is caught in hook.
-
Clean hook (see page 68 - 69).
Stitches are irregular.
* Needle size is not correct for thread and fabric (see page
26 - 27).
0DFKLQHLVQRWWKUHDGHGFRUUHFWO\VHHSDJH
* Top thread tension is too loose (see page 28 - 29).
* Fabric is being pulled or pushed against machine feeding
action.
-
Guide it gently.
* Bobbin has not been wound evenly.
-
Rewind bobbin.
Needle breaks.
* Fabric is being pulled or pushed against machine feeding
action.
-
Guide it gently.
* Needle size is not correct for thread and fabric (see page
26 - 27).
* Needle is not all the way up into the needle clamp (see page
26 - 27).
* Twin needle is being used but stitch width is set too wide (see
page 70 - 71).
* Too much thread appears on the underside of stitching.
* Upper thread not correctly thread (see page 20 - 21).
THREAD PROBLEMS
Thread bunches.
* Top and bobbin threads are not drawn back under presser
foot before starting seam.
-
Draw both threads back under
presser foot about 6 inches (10 cm) and hold until a few
stitches are formed.
Needle thread breaks.
0DFKLQHLVQRWWKUHDGHGFRUUHFWO\VHHSDJH
* Top thread tension is too tight (see page 28 - 29).
* Needle is bent.
-
Replace needle (see page 26 - 27).
* Needle size is not correct for thread and fabric (see page
26 - 27).
Bobbin thread breaks.
* Bobbin case is not threaded correctly (see page 18 - 19).
* Lint accumulates in bobbin case or hook.
-
Remove lint
(see page 68 - 69).
Fabric puckers.
* Top thread tension is too tight.
-
Adjust thread tension
(see page 28 - 29).
* Stitch length is too long for sheer or soft fabric.
-
Shorten
stitch length.
6. PERFORMANCE CHECKLIST
94


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer S800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer S800 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info