616506
44
Zoom out
Zoom in
Previous page
1/46
Next page
42 47
Adjusting stitch length
Needle thread tension
Any stitch length setting from 1 to 5 will give you
an open zig-zag stitch.
The higher the number, the more open, or
further apart your stitches will be.
The area between 0 and 1 on the dial is used for
satin stitching, a series of closely spaced plain
zig-zag stitches that form a smooth satin-like
surface.
The needle thread tension dial regulates the
amount of tension on the needle thread and lets
you select just the right setting for your fabric
and thread.
The correct tension setting will produce a
smooth even stitch (1).
Too much tension will produce a tight stitch (2),
causing fabric to pucker. Loosen tension by
turning dial to a lower number.
Too little tension will produce a loose stitch (3),
causing loops in your pattern. Tighten tension
by turning dial to a higher number.
Ajuste longitud del punto
Tensión hilo de la aguja
Cualquier posición para la longitud del punto
desde 1 a 5, le proporcionará un punto de zig-
zag abierto.
Cuanto más alto sea el número, más abiertas o
más separadas estarán las puntadas.
El área entre 0y1eneldial, se utiliza para punto
de realce, que es una serie de puntadas en zig-
zag plano muy juntas, que forman una
superficie muy suave como de satin.
El dial de tensión le permite regular la tensión
del hilo de la aguja. La posición correcta de la
tensión producirá una puntada suave y
uniforme con el hilo superior y el inferior unidos
en las esquinas del zig-zag.
El hilo superior puede verse en el reverso del
tejido en graduación variada, dependiendo del
hilo, tejido y tamaño del punto que esté
aplicando (1).
Demasiada tensión producirá un punto prieto
que causará frunces en eltejido (2). Para reducir
estos frunces, gire el dial de tensión hacia una
posición inferior. En algunos tejidos esto puedo
ocasionar que la unión del punto en las
esquinas, por el reverso, no sean perfectas.
Poca tensión producirá que el punto esté flojo.
En muchos casos se formarán lazos en el
reverso del tejido. Aumentar la tensión girando
el dial a una posición más alta (3).
Ajuste longitud del punto
Tensión hilo de la aguja
Cualquier posición para la longitud del punto
desde 1 a 5, le proporcionará un punto de zig-
zag abierto.
Cuanto más alto sea el número, más abiertas o
más separadas estarán las puntadas.
El área entre 0 y 1 en el dial, se utiliza para punto
de realce, que es una serie de puntadas en zig-
zag plano muy juntas, que forman una
superficie muy suave como de satin.
El dial de tensión le permite regular la tensión
del hilo de la aguja. La posición correcta de la
tensión producirá una puntada suave y
uniforme con el hilo superior y el inferior unidos
en las esquinas del zig-zag.
El hilo superior puede verse en el reverso del
tejido en graduación variada, dependiendo del
hilo, tejido y tamaño del punto que esté
aplicando (1).
Demasiada tensión producirá un punto prieto
que causará frunces en eltejido (2). Para reducir
estos frunces, gire el dial de tensión hacia una
posición inferior. En algunos tejidos esto puedo
ocasionar que la unión del punto en las
esquinas, por el reverso, no sean perfectas.
Poca tensión producirá que el punto esté flojo.
En muchos casos se formarán lazos en el
reverso del tejido. Aumentar la tensión girando
el dial a una posición más alta (3).
Point invisible
(seulement pour machines avec
5, 6, 8 et 10 points)
Le point caché vous permet de coudre les
ourlets de tissus moyens épais et jersey. Coudre
au point caché requiert un peu de pratique.
Faites un exercice.
Sélection de point: Point invisible (C)
Position d’aiguille:
Largeur de point:
Longueur de point: 1- -
Pied presseur: Spécial pour
point invisible 9
plaque à aiguille: Universelle (A)
L’envers de l’ouvrage vers vous, tournez l’ourlet
comme illustré, en formant un pli à environ 0,5cm
du bord coupé de l’ourlet. Epinglez les trois
épaisseurs ainsi repliées.
Positionnez l’ourlet sous le pied presseur, le pli
contre le bord du guide, comme illustré.
Baissez le pied presseur et commencez à
piquer. Les points droits doivent se trouver sur
le bord de l’ourlet, les points zig-zag doivent
piquer dans le pli du tissu. Réglez la largeur du
point afin que les points zig-zag transpercent
très peu le tissu. Piquez lentement en dirigeant
bien le tissu plié le long di guide.
Si vous avez bâti votre travail aux épingles
retirez les épingles au fur et à mesure de la
piqûre.
Réglages recommandés
½à2 ½
Préparez le pliage de l’ourlet et repassez
légèrement. mieux vaut bâtir l’ourlet pour le
maintenir en place (comme illustré). Ce bâti doit
se situer à 1,2cm de la pliure de l’ourlet.
34 512
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer HD110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer HD110 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info