467705
40
Zoom out
Zoom in
Previous page
1/44
Next page
40
CHECK CHART FOR PERFORMANCE
PROBLEMS
GENERAL PROBLEMS
Machine does not sew.
* Foot control is not connected.
-
See page 8.
* Power switch is turned off.
-
Turn on the switch.
Machine jams/knocks.
* Thread is caught in hook.
-
Clean hook (see page 38).
* Needle is damaged.
-
Replace needle (see page 24 - 25).
Fabric does not move.
* Presser foot is not lowered
-
lower presser foot.
* Stitch length is set at 0.
-
Set it at 1 to 4.
STITCHING PROBLEMS
Machine skips stitches.
* Needle is not all the way up into needle clamp.
-
See page 24 - 25.
* Needle is bent or blunt.
-
Replace needle (see page 24 - 25).
* Machine is not threaded correctly.
-
See page 12.
* Thread is caught in hook.
-
Clean hook (see page 38).
Stitches are irregular.
* Needle size is not correct for thread and fabric.
-
See page 24 - 25.
* Machine is not threaded correctly.
-
See page 12.
* Top thread tension is too loose.
-
See page 23.
* Fabric is being pulled or pushed against machine feeding action.
-
Guide it gently.
* Bobbin has not been wound evenly.
-
Rewind bobbin.
Needle breaks.
* Fabric is being pulled or pushed against machine feeding action.
-
Guide it gently.
* Needle size is not correct for thread and fabric.
-
See page 24 - 25.
* Needle is not all the way up into the needle clamp (See page 24 - 25).
THREAD PROBLEMS
Thread bunches.
* Top and bobbin threads are not drawn back under presser foot
before starting seam.
-
Draw both threads back under presser foot
about 4 inches (10 cm) and hold until a few stitches are formed.
Needle thread breaks.
* Machine is not threaded correctly.
-
See page 12.
* Top thread tension is too tight.
-
See page 23.
* Needle is bent.
-
Replace needle (see page 24 - 25).
* Needle size is not correct for thread and fabric
-
See page 24 - 25.
Bobbin thread breaks.
* Bobbin case is not threaded correctly. See page 11.
* Lint accumulates in bobbin case or hook.
-
Remove lint
(see page 38).
Fabric puckers.
* Top and bobbin thread tensions are too tight.
-
Adjust thread tensions
(see page 23).
* Stitch length is too long for sheer or soft fabric.
-
Shorten stitch length.
COME RIMEDIARE A PICCOLI INCONVENIENTI
GUASTI COMUNI
La macchina non cuce
* Il cavo di collegamento non è inserito nelia spina.
-
Vedi pag. 8.
* Il selettore delia velocità è disinserito.
-
Metterio su 1 o 2.
Macchina bloccata
* I fili sono impigliati nel crochet.
-
Pulire o ii crochet (vedi pag. 38).
* L'ago è danneggiato.
-
Togliere I'ago. (vedi pag. 24 - 25).
La macchina non trasporta
* Il piedino è posizionato in alto.
-
Abbassare il piedino.
* La lunghezza del punto è regolata su 0.
-
Regolaria da 1 a 4.
* Il copri griffa è inserito.
-
Estrarre il copri-griffa.
PROBLEMI DI PUNTI
Punti saltati
* L'ago non è inserito correttamente
-
(vedi pag. 24 - 25).
* L'ago è piegato oppure è spuntato.
-
Cambiare I'ago (vedi pag. 24 - 25).
* La macchina non è infilata bene.
-
Vedi pag. 12.
* Fill impigliati nel crochet.
-
Pulire il crochet. (vedi pag. 38).
Punto irregolare
* L'ago non è adatto alla stoff a e al filo. (vedi pag. 24 - 25).
* La macchina non è infilata correttamente.
-
Vedi pag. 12.
* La tensione del filo superiore è allentata. Vedi pag. 23,
* Avete tirato sulla stoffa oppure I'avete spinta contro la direzione di
trasporto
-
Guidare la stoffa delicatamente.
* Il filo inferiore non è avvolto regolarmente.
-
Avvolgerlo di nuovo.
L'ago si rompe
* Avete tirato la stoffa oppure I'avete spinta contro la direzione del trasporto.
-
Guidare la stoffa delicatamente.
* La misura dell'ago non è adatta alla stoffa e al filo.
-
Vedi pag. 24 - 25.
* L'ago non è spinto a fondo nel porta-ago.
-
Vedi pag. 24 - 25.
PROBLEMI CON I FILI
I fili si aggrovigliano
* Il filo superiore e quello inferiore prima dell'inizio della cucitura non sono
tirati indietro sotto il piedino. Tirate tutti e due i fili circa 10 cm. sotto il
piedino e fissateli leggermente con qualche punto.
Il filo superiors si rompe
* La macchina non è infilata correttamente.
-
Vedi pag. 12.
* La tensione del filo superiore è eccessiva.
-
Vedi pag. 23.
* L'ago è piegato.
-
Cambiare I'ago. Vedi pag. 24 - 25.
* La misura dell'ago non è adatta alla stoffa e al filo.
-
(vedi pag. 24 - 25).
Il filo inferiore si rompe
* La bobina non è inserita correttamente.
-
Vedi pag. 11.
* Filaccia intasa la bobina o ii crochet. Togliere la filaccia.
-
(vedi pag. 38).
La stoffa si raggrinza
* La tensione del filo superiore ed inferiore è eccessiva. Allentare la tensione
del filo.
-
(vedi pag. 23).
* La lunghezza del punto per stoffa leggera e morbida è eccessiva.
Accorciare la lunghezza del punto.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 118 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 118 in the language / languages: English, German, Italian as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info