634624
2
Zoom out
Zoom in
Previous page
1/2
Next page
Mounting location of base station
Avoid installing the base station behind other electrical and electronic devices, as
they may interfere with the signal and consistency of wireless communication.
The base station should be at least 2 meters away from any other Bluetooth or wire-
less LAN (WiFi) transceiver.
It is advisable to check Bluetooth connection throughout the boat by pairing the
unit before permanently mounting the base station.
Operation
Keys and LED Action Mode: Auto Standby Wind NoDrift
< Left arrow Port or
> Right arrow Starboard
Short press: Adjust 1° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind mode.
Long press (2s): Adjust 10° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind
mode.
< Left arrow +
> Right arrow
Autotack (in Wind mode), press and hold until LED is flashing green rapidly, then press AUTO to confirm.
STBY Place the autopilot into Standby mode.
MODE Changes the autopilot mode:
1. Boats set to SAIL: Toggles AUTO and WIND modes.
2. Other boat types: Toggles AUTO and NoDrift modes.
AUTO Engages the autopilot into AUTO mode.
LED* Green for 1s indicates message acknowledged. Red for 1s indicates message is either rejected or not acknowledged.
Green rapid flashes for up to 10s, followed by solid green for 1s. Red for 1s indicates message is either rejected or not
acknowledged.
* Note: In addition to the LED behaviour specified: Red will flash for 1s every 10s when battery level is low.
X X
X
X
Electromagnetic
Interference
0.5 m (20”) Min 0.5 m (20”) Min
2 m (6 ft) Min
RADAR
Magnetic Field
Radio Transmitter
X
Surface mount the base station
3 mm
19 mm
1
4
5
3
2
Use of Lanyard strap or wristband Add/replace batteries
WR10 Wireless Autopilot Controller operates
on 2 AAA batteries. Remove the cover to add
or replace the batteries.
Wiring the base station
A
1.8 m (6 ft) Micro-C drop
cable (male to female)
B
Micro-C T-Joiner
C
Micro-C backbone
A
B
C
First, make sure that:
- the batteries in the remote are not low.
- the remote and the base station are placed as close together as possible.
- the AP system is OFF or in standby.
Then continue to:
1. Remove power from the base station.
2. Press and hold the buttons MODE and STBY on the remote for at least 5 seconds
until a single quick green LED flashes. The remote is now in Discoverable mode and
will stay in this mode for 60 seconds or until base station asks to pair.
3. Power up base station. For the first 10 seconds, the base station will search for
Discoverable remotes.
4. Wait till remote quickly flashes the green LED every second, indicating that the base
station is asking to pair.
5. Press the AUTO button for at least 1 second to start the pairing.
- When succesfully paired: The green LED will stay on for 2 seconds.
- When pairing failed: The red LED will stay on for 2 seconds.
Pairing a remote to the base station
Use Philips screw-
driver size #1 to en-
sure proper torque
when reassembling.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Simrad WR10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Simrad WR10 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info