Rounding selector switchRundung-Wahlschalter Afronding-keuzeschakelaarInterrupteur de sélection d'arrondissagePrzełącznik zaokrąglenia
UP
Always round the decimal digits up.Immer aufrunden von Dezimalstellen.De digitale cijfers altijd naar boven afrondenToujours arrondir les nombres décimaux au nombre supérieurZawsze zaokrąglaj w górę pozycje dziesiętne.
5/4
Round digits below 5 down and above 5 up.
• Abrunden, wenn Dezimalstelle kleiner 5
• Aufrunden, wenn Dezimalstelle größer 5
• De cijfers lager dan 5 naar onder en hoger dan 5 naar boven
afronden
• Arrondir les chiffres inférieurs à 5 au nombre inférieur et les chiffres
supérieurs à 5 au nombre supérieur
• Zaokrąglanie w dół, gdy pozycja dziesiętna mniejsza niż 5.
• Zaokrąglanie w górę, gdy pozycja dziesiętna większa niż 5.
CUT
Always round the decimal digits down.Immer abrunden von Dezimalstellen.De digitale cijfers altijd naar onder afrondenImmer abrunden von Dezimalstellen.Zawsze zaokrąglaj w dół pozycje dziesiętne.
Decimal point selector switchDezimalpunkt-Wahlschalter Decimaalpunt-keuzeschakelaarInterrupteur de sélection de la marque décimalePrzełącznik kropki dziesiętnej
F
Show all displayable decimal digits.Zeigt alle darstellbaren Dezimalstellen an.Alle mogelijke weer te geven decimale cijfers tonen.Afficher tous les nombres décimaux affichablesWyświetla wszystkie możliwe do wyświetlenia pozycje dziesiętne.
3, 2, 0
Limit the displayed decimal digits to the respective count.Zeigt nur Dezimalstellen bis zur jeweiligen Stelle an.
Het aantal weer te geven decimale cijfers tot het respectievelijk getal
beperken.
Limiter les nombres décimaux affichés au compte respectifWyświetla pozycje dziesiętne tylko do danej pozycji.
Calculation selector switchKalkulation-WahlschalterBerekening-keuzeschakelaarInterrupteur de sélection de calculPrzełącznik obliczeń
PROFIT
Depends on selected function
Perform the cost, sell and profit margin calculations with COST,
SELL, MGN.
Abhängig von der gewählten
Funktion
Verkaufspreis und Gewinnmarge-Rechnung mit COST, SELL,
MGN durchführen
Afhankelijk van de gekozen
functie
Kosten, verkoopprijs en winstmarge-berekeningen uitvoeren
met COST, SELL, MGN.
Dépend de la fonction
sélectionnée
Exécute les calculs du coût, de vente et de la marge de
profit avec COST, SELL, MGN
Zależnie od wybranej funkcji
Obliczenie ceny sprzedaży i marży za pomocą COST,
SELL, MGN
TAX
Perform the tax calculations with SET, TAX+, TAX-.Steuerrechnung mit SET, TAX+ und TAX durchführen.Belastingsberekeningen uitvoeren met SET, TAX+, TAX-.Exécute les calculs de taxe avec SET, TAX+, TAX-Obliczenie podatku za pomocą SET, TAX+ i TAX
COST
SET
Set cost/tax rate (depend on selected function)Kosten/Steuersatz festlegen
Het kost/belastingtarief invoeren (afhankelijk van de gekozen
functie)
Réglage du coût/taux de taxe (selon la fonction
sélectionnée)
Ustalenie kosztów/stawki podatkowej
SELL
TAX+
Set current value as selling price or add tax to current value
(depend on selected function)
Aktuellen Wert als Verkaufspreis festlegen / Steuer
hinzuzuaddieren.
De huidige waarde als verkoopprijs instellen of belasting aan
de huidige waarde toevoegen (afhankelijk van de gekozen
functie)
Réglage de la valeur en cours comme prix de vente ou
ajouter la taxe à la valeur en cours (selon la fonction
sélectionnée)
Ustalenie bieżącej wartości jako ceny sprzedaży /
Dodanie podatku
MGN
TAX-
Set current value as profit margin or subtract tax to current value
(depend on selected function)
Aktuellen Wert als Gewinnmarge festlegen / Steuer subtrahieren.
De huidige waarde als winstmarge instellen of belasting aan de
huidige waarde aftrekken (afhankelijk van de gekozen functie)
Réglage de la valeur en cours comme prix de vente ou
soustraire la taxe à la valeur en cours (selon la fonction
sélectionnée)
Ustalenie bieżącej wartości jako marży zysku/ Odjęcie
podatku
AC
Power ON/All Clear (incl. memory, excl. tax rate)Einschalten/Alles löschen (inkl. Memory, exkl. Steuersatz)Inschakelen/Alles wissen (incl. geheugen, excl. belastingtarief)MARCHE/Tout effacer (incluant la mémoire, excluant le taux de taxe)
Włączenie/Skasowanie wszystkiego (łącznie z Memory, oprócz stawki
podatkowej)
Backspace: delete last entered digit.Zurück: löscht die letzte ZahleingabeBackspace: Het laatste ingevoerde cijfer verwijderen.Touche Retour : pour supprimer le dernier chiffre entréWstecz: kasuje ostatnio wprowadzoną cyfrę
Memory clear: Erase stored valuesLöscht den gespeicherten Wert.Geheugen wissen: Opgeslagen waarden wissenEffacer mémoire : Effacer les valeurs enregistréesKasuje wartość zapisaną w pamięci.
MR
Memory recall: Recall stored value to current calculation. Fügt der Rechnung den gespeicherten Wert zu.
Geheugen oproepen: Opgeslagen waarde voor huidige berekening
oproepen.
Rappel de mémoire : Rappeler la valeur enregistrée dans le calcul
en cours
Dodaje do rachunku wartość zapisaną w pamięci.
M-
Memory subtraction: Subtract current value from stored value. Subtrahiert den aktuellen Wert vom gespeichterten Wert.
Geheugen aftrekking: Huidige waarde van opgeslagen waarde
aftrekken.
Soustraction de mémoire : Soustraire la valeur en cours de la valeur
enregistrée
Odejmuje bieżącą wartość od wartości zapisanej w pamięci.
M+
Memory addition: Add current value to stored value. Addiert den aktuellen Wert zum gespeicherten Wert.Geheugen optelling: Huidige waarde bij opgeslagen waarde optellen.
Addition de mémoire : Ajouter la valeur en cours de la valeur
enregistrée
Dodaje bieżącą wartość do wartości zapisanej w pamięci.
E
OVERFLOW
An invalid calculating operation (e.g. division by 0) is carried out, the
amount of a calculated result is larger than 9,999,999,999. or number
entry exceeds 10 digits. No further entries can be taken. Press
“C·CE” key to confirm the mistake.
ÜBERLAUF
Wenn eine ungültige Rechenoperation (z.B. Division durch 0)
durchgeführt wurde, bei der die Summe des Rechenergebnisses
größer als 9,999,999,999. ist oder die Eingabe 10 Ziffern übersteigt,
erscheint ein “E” in der Anzeige. Keine weiteren Eingaben möglich.
Mit “C·CE” Taste, den Fehler bestätigen.
OVERLOOP
Een ongeldige berekening (bijv. delen door 0) werd uitgevoerd, het
getal van een berekend resultaat is groter dan 9,999,999,999. of de
invoer overschrijdt 10 cijfers. Het toestel neemt geen verdere invoer
aan. Druk op de “C.CE” toets om de fout te bevestigen.
EXCÉDENT
Une opération de calcul invalide (ex: division par 0) est effectuée,
le montant du résultat calculé est supérieur à 9 999 999 999 ou le
nombre est composé de plus de 10 chiffres. Aucune nouvelle entrée
ne pourra être admise. Appuyez sur la touche «C.CE» pour confirmer
l’erreur.
NADMIAR
Jeżeli została wykonana niepoprawna operacja rachunkowa (np.
dzielenie przez 0), w której na wyświetlaczu pojawia się „E”. Dalsze
wprowadzanie nie jest możliwe. Potwierdź błąd klawiszem „C CE”.
CLEANING AND CARE
Clean the product with a slightly damp cloth and then dry them
thoroughly. Make sure that no water enters the product interior (for
example, through the switch or buttons).
REINIGUNG UND PFLEGE
Reinigen Sie das Produkt nur mit einem leicht angefeuchteten Tuch
und trocknen Sie sie anschließend gut ab. Darauf achten, dass
kein Wasser (z.B. an den Schaltern und Tasten) ins Produktinnere
gelangt.
REINIGING EN ONDERHOUD
Reinig het product met een licht bevochtigde doek en droog het
vervolgens grondig. Zorg dat er geen water het apparaat binnendringt
(bijvoorbeeld via de schakelaar of knoppen).
NETTOYAGE ET ENTRETIEN
Nettoyez le produit avec un chiffon légèrement humide puis séchez-le
complètement. Assurez-vous que de l’eau ne pénètre pas à l’intérieur
du produit (par exemple, par l’interrupteur ou par les boutons).
CZYSZCZENIE I PIELĘGNACJA
Produkt czyść lekko nawilżoną ściereczką i dobrze go wysusz.
Zwracaj uwagę na to, by woda nie dostała się do wnętrza (np. na
klawiszach i przełącznikach).
C
DEFGHIJK
NMLAB
4
3
2
1
5
(IM)36-005221_DC057-10+DC057W-10_Multi-IM_V1_160125.indd 125/1/16 9:01 AM
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sigma DC057-10 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sigma DC057-10 in the language / languages: English, German, Dutch, French as an attachment in your email.
The manual is 4,82 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.