555850
3
Zoom out
Zoom in
Previous page
1/26
Next page
Building Technologies 74 319 0614 0 c 20.05.2008 3/26
Anschlussschaltpläne
Siehe Abbildungen
5
11
auf Seite 24
Für Kleinspannung Für Netzspannung
5
Brauchwassertemperaturmessung mit Fühler (nur
Typ RVP211)
6
Externer Schalter zur Betriebsarten-Umschaltung
7
Brauchwassertemperaturmessung mit Thermostat
(nur Typ RVP211)
8
Anschluss Dreipunktstellantrieb, Heizkreispumpe
und (nur Typ RVP211) Brauchwasserladepumpe
9
Anschluss Brenner (Kesseltemperaturregelung)
10
Anschluss Zweipunktstellantrieb (Vorlauftempera-
turregelung)
11
Anschluss Stellantrieb für Brauchwasser-
Umlenkventil (nur Typ RVP211)
A6 Raumgerät
B1 Vorlauf- bzw. Kesseltemperaturfühler
B3 Brauchwassertemperaturfühler (nur Typ RVP211)
B9 Witterungsfühler
E1 Brenner
F1 Temperaturwächter
F2 Sicherheitstemperaturbegrenzer
F3 Brauchwasserthermostat (nur Typ RVP211)
M1 Heizkreispumpe
M3 Brauchwasserladepumpe (nur Typ RVP211)
N1 Regler RVP201/211
S1 Externer Schalter
Y1 Dreipunktstellantrieb
Y2 Zweipunktstellantrieb
Y3 Stellantrieb für Umlenkventil (nur Typ RVP211)
en English
Do not throw these instructions away but keep
them with the controller!
Only the RVP211 provides D.h.w. heating.
Installation
Place of installation
In a dry place, e.g. the boiler room.
Mounting choices:
- In the control panel, on the inner wall or on a top hat
rail (EN 60715)
- On a panel
- In the control panel front
- In the sloping front of a control desk
Permissible ambient temperature: 0…50 °C
Electrical installation
- Local regulations on electrical installations must be complied
with
- Cable tension relief must be assured
- The cables from the controller to the actuator and the pump
carry mains voltage
- The cables to the detectors should not be run parallel to mains
carrying cable (insulation class II to EN 60730!)
Specifications of cable
Maximum permissible cable lengths to the detectors and the
room unit:
Copper cable 0.6 mm dia.: 30 m
Copper cable 0.5 mm
2
: 50 m
Copper cable 1.0 mm
2
: 80 m
Copper cable 1.5 mm
2
: 120 m
Installing and wiring the base
Wall mounting
1. Separate base from the controller.
2. Hold base against the wall. Marking "TOP" must be at the
top!
3. Mark fixing holes on the wall.
4. Drill holes.
5. If required, knock out holes on the base for fitting cable entry
glands.
6. Secure base.
7. Wire up base.
Top hat rail mounting
1. Fit top hat rail.
2. Separate base from the controller.
3. If required, knock out holes on the base for fitting cable entry
glands.
4. Fit base to the rail. Marking "TOP" must be at the top!
5. If required, secure the base (depending on type of top hat rail
used).
6. Wire up base.
Flush panel mounting
- Maximum thickness: 3 mm
- Panel cutout required: 138 × 92 mm
1. Separate base from the controller.
2. If required, knock out holes on the base for fitting cable
entry glands.
3. Insert base in the panel cutout from behind until stop is
reached. Marking "TOP" must be at the top!
4. Push lateral tongues behind the front panel:
Refer to figure
1
on page 24
Place tongues correctly on the left and on the right. They
must not be inside the cutout!
5. Wire up base. Make sure the cable lengths will be adequate
so that the control panel door can be opened.
Fitting the controller to the base
1. Make sure that position and orientation of the turning levers
are correct, using the fixing screws (illustration shows the lat-
eral wall of the controller casing):
Refer to figure
2
on page 24
2. Insert controller in the base until stop is reached. Marking
"TOP" must be at the top!
3. Tighten fixing screws gradually
Fitting a time switch
If a time switch is to be fitted (weekly or digital time switch), the
respective opening in the cover must be cut out with a knife.
Readjusting the clock after a power failure
When power returns after a power failure, the clock will be read-
justed. Automatic readjustment can be aborted by briefly setting
the operating mode selector to manual operation
and then
back to the required operating mode, allowing manual adjustment
of the clock.
Commissioning
Plant-specific settings
Setting elements: refer to illustration on page 4.
The coding switches and setting potentiometers for the plant-
specific settings are accessible after removal of the time switch.
- Removing the time switch: pull dial away from the controller.
- Fitting the time switch: insert time switch and push it down
(audible click).
Checking the motorized valve
Check the seat or slipper valve: see if
- it is correctly installed (observe direction of flow indicated on
the valve body)
- the slipper moves in the correct angular range (note position
indicator)
- the manual level is disengaged
Exercise caution with underfloor and ceiling
heating systems!
The limit thermostat must be correctly set. During the functional
check, the flow temperature may not exceed the maximum per-
missible level (usually 55 °C). If it does, proceed immediately as
follows:
- Either close the seat or slipper valve manually, or
- Switch off the pump, or
- Close the pump isolating valve
Commissioning the controller
1. Check wiring according to the plant connection diagram.
2. Switch on power supply.
3. Check LED for "Override":
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RVP201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RVP201 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RVP201

Siemens RVP201 User Manual - English - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info