41499
4
Zoom out
Zoom in
Previous page
1/16
Next page
4/16 03.07.2003 CE1G2266xx
7 Reset
Benutzerdefinierte Daten:
Taste hinter der Nadelöffnung mindestens eine Sekunde
drücken: Dadurch werden die benutzerspezifischen
Einstellungen und die „selbstlernende adaptive Regelung“,
sowie die Anzeigen der Vorlauftemperatur,
Aussentemperatur und Brauchwasser-Sollwert auf ihre
Standardwerte zurückgesetzt (die „Fachmann“-
Einstellungen bleiben unverändert). Die Uhr beginnt bei
12:00. Während der Resetzeit leuchten alle Anzeigefelder
des Displays, und können so überprüft werden.
Alle benutzerdefinierten Daten plus Heizfachmann-
Einstellungen:
Taste hinter der Nadelöffnung zusammen mit der Wärmer-
und Kältertaste mindestens eine Sekunde drücken.
Nach diesem Reset werden die Werkseinstellungen neu
geladen (siehe auch Abschnitt „Werkseinstellungen“ in der
Bedienungsanleitung).
Achtung: Wird das Gerät länger als 30 Sekunden
vom Sockel entfernt, erscheint eine Fehler-
meldung auf dem Display.
Beim Zurückschieben auf den Sockel muss
die Fehlermeldung nach spätestens
2 Minuten verschwinden.
Ohne eingesetzte Batterien funktioniert der
Reset nur während maximal 15 Sekunden
nach Entfernen des REV23M vom Sockel
korrekt.
8 Hinweise
REV23M ist ein elektronischer Raumtemperaturregler
mit Wochenschaltuhr.
Der Regler gehört zur Softwareklasse A und ist für den
Gebrauch in einer Umgebung mit normalem
Verschmutzungsgrad vorgesehen.
Sollten im Referenzraum thermostatische
Heizkörperventile installiert sein, müssen diese
vollständig geöffnet werden.
Der Fernbedienungskontakt muss getrennt, d.h. mit
einem separaten, abgeschirmten Kabel verdrahtet
werden.
Die örtlichen Vorschriften für Elektroinstallationen sind
einzuhalten.
REV23M kann nur zusammen mit einem
OpenTherm Plus-fähigen Kessel betrieben werden.
Commissioning
1 Mounting
Remove controller from its base by proceeding according
to Fig. A.
For mounting, refer to Figs. B and C and “Mounting notes“.
2 Check wiring
For the electrical connections, refer to “Connection
diagram“ (also refer to Figs. D and E).
Note: Do not use stranded wires, only solid wires or
stranded wires with ferrules.
3 Remove the battery transit tab
As soon as the battery transit tab is removed, the controller
starts to operate (also refer to Fig. F).
If there is no display, check the correct fitting and function
of the batteries.
4 Configuration
4.1 Accessing the heating engineer level
The heating engineer level will be enabled by pressing
simultaneously the warmer and colder buttons and by
rolling the roller selector away from the display and then
toward the display (also refer to Fig. H).
4.2 Functions
4.2.1 Calibrating the temperature sensor
After activating the heating engineer level, the CAL symbol
will flash. When pressing the roller selector, the room
temperature currently acquired flashes and can now be
recalibrated by a maximum of ± 2 °C by rolling either
toward the display or away from it. To store the re-
calibration, press the roller selector (also refer to Fig.
).
4.2.2 Setpoint limitation
There are 2 setting choices available:
or
On the heating engineer level, change from the flashing
CAL symbol to the setpoint limitation symbol by rolling
toward the display (also refer to Fig
).
Press to accept. 5...29 °C will flash (factory setting).
Press to accept or continue rolling.
Setting 16...29 °C will flash. Press to accept.
4.2.3 Optimum start control
On the heating engineer level, change from the flashing
CAL symbol to the optimum start control symbols
by rolling twice toward the display
(also refer to Figs.
and ).
Press to accept.
will flash (factory setting).
Press to accept or continue rolling until you reach ½, 1 or
optimization OFF
. Press to accept.
4.2.4 Control mode
On the heating engineer level, change from the flashing
CAL symbol to the symbols of the various control modes
by rolling away from the display (also refer to Fig.
).
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV23M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV23M in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV23M

Siemens REV23M User Manual - English - 4 pages

Siemens REV23M User Manual - German - 2 pages

Siemens REV23M User Manual - Dutch - 2 pages

Siemens REV23M User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info