462306

Siemens REV17 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
REV17 User Guide Room temperature controller REV17 Page 1 of 2
REV17 User Guide SIEMENS BUILDING TECHNOLOGIES
Slider Positions
RUN
Slider positions
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Time setting
Date Day / Month
/ Year
Weekdays 1-5
Weekend 6-7
1, 2 or 3
Comfort phases
Start time
Comfort phase 1
Temperature
Comfort phase 1
End
Comfort phase 1
Start time
Comfort phase 2
Temperature
Comfort phase 2
End
Comfort phase 2
Start time
Comfort phase 3
Temperature
Comfort phase 3
End
Comfort phase 3
Saving temp.
time program
Start
Absence
Temperature
Absence
End
Absence
Temperature
remote control
If the selected operating mode does not support the setting, the time display shows PASS.
STEP Symbol
Programming
1
Initial Start Up - Enabling Battery Power
Remove the controller from the mounting base and pull out the black insulating tape tab from the battery compartment: The controller
turns on automatically. Re-insert the controller in the mounting base.
:
2
Language Selection
After startup, a welcome message appears for approx 2 minutes. Press a button to interrupt the message. Language selection starts
with “ENGLISH“ (factory setting). Press
:
or until your desired language appears. Press or move the slider to accept
your language choice.
Hint: if you choose the incorrect language, an Expert Level Reset will need to be performed. This is achieved by:
Pressing simultaneously the DIP switch reset button (on the back of the unit under the dip switch cover) and the
and
for 5 seconds: After this reset, all factory settings will be reloaded. This applies to both the slider settings and the
settings made on the expert level
.
3
Move the Slider to position 1 (time setting): Press
Setting Time:
or to set the time.
4
Slider in position 2 (date: day/month/year): Press
Setting Date:
or to set the date. (Note: the day of the week is automatically chosen)
5
Slider in position 3 (Monday- Friday weekdays
Weekday (1-5) and Weekend (6-7) Blocks:
, Saturday and Sunday weekend ): You will notice the flashing
or blocks in the top right hand corner. Press the or to toggle between both blocks.
6
Slider in position 4 (there are 3 comfort phases): Press
Comfort Phases:
or to set the comfort phases you desire.
7
Slider in position 5 (start time comfort phase 1): Press
Setting Time in Comfort Phase 1:
or to set the start time.
Hint: you will notice the flashing time cursor on the 24 hour time bar (at the bottom of the screen) corresponding with the
entered time, moves as you adjust the time with the
or buttons
8
Slider in position 6 (temperature comfort phase 1): Press
Setting Temperature in Comfort Phase 1:
or to set the temperature.
9
Slider in position 7 (end time comfort phase 1): Press
Setting Time to End Comfort Phase 1:
or to set the end time.
10
, ,
, ,
Slider positions 8…10 (comfort phase 2) and slider positions 11…13
(comfort phase 3): Same procedure as above for comfort phase 1.
Setting Time and Temperature for Comfort Phase 2 and 3:
11
Slider in position 14 (energy saving temperature in time switch programs Automatic and Exception day): Press
Setting Energy Saving Temperature from Monday to Sunday:
or to set the
temperature.
Note: The energy saving temperature is valid Monday through Sunday. It does not depend on operating mode "Continuous
energy saving".
Hint: If you do not want your heating to come on at night (or anytime it is controlling to the setpoint) then set this value low e.g. 3.0°C
12
RUN
Complete Programming Move the slider to RUN position and close the cover.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV17 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV17 in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV17

Siemens REV17 User Manual - German - 2 pages

Siemens REV17 User Manual - Dutch - 2 pages

Siemens REV17 User Manual - French - 2 pages

Siemens REV17 Installation Guide - All languages - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info