41505
4
Zoom out
Zoom in
Previous page
1/8
Next page
4/8
Siemens Building Technologies Room temperature controller REV100 CE1N2211en
Landis & Staefa Division 16.05.2000
Select the economy temperature and press the time button, then enter the num-
ber of days you are absent
(max. 99 days). The display will show the num-
ber of days and the holiday symbol. Every midnight, the counter subtracts one day.
When the day counter reaches 00, the 24-hour operation with two heating phases will
automatically be resumed.
Press the day counter and set it to 00.
If the temperature displayed does not agree with the room temperature effectively
measured, the temperature sensor can be re-calibrated. For that purpose, set the DIP
switch for Sensor Alignment to ON and press the DIP switch button.
Press
to bring the flashing room temperature in line with the room temperature
currently measured. The increments for the readjustment are 0.2°C {max. ±2 °C).
When balancing of the sensor is completed, the DIP switch must be reset to OFF.
Before cleaning the display or to prevent tampering, the display buttons can be locked.
Press the button behind the little hole for a short moment (max. 1 second):
ap-
pears and all other displays disappear. The display buttons are now disabled while all
the other functions are fully maintained.
Press the button behind the little hole again (max. 1 second).
Keep the button behind the little hole depressed for at least 3 seconds. This resets the
individual settings and the time of day to their default values. During the reset time of 3
seconds, the display will be fully lit, allowing the proper functioning of the display to be
checked. After each reset, all personal settings such as time of day, weekday, switch-
ing points, temperature setpoints, sensor calibration, etc., must be re-entered.
About three months before the batteries are exhausted, the display shows the battery
symbol
. The other displays disappear, the display buttons are deactivated while
all the other functions are fully maintained. When changing the batteries, the current
data will remain stored for at least one minute.
Using a suitable remote operating unit, the REV100 can be switched to economy mode
. Changeover takes place by closing a SRWHQWLDOIUHHFRQWDFW connected to terminals
T1 and T2. In that case, symbol
appears on the display. When the contact opens,
the selected operating mode will be reactivated.
Operation according to controller setting Continuous economy temperature
T2
T1
2252Z05
T2
T1
2252Z06
Suitable remote operating units: telephone modem, manual switch, window switch,
occupancy detector, control centre, etc.
Enter
Cancel
6HQVRUFDOLEUDWLRQ
/RFNLQJWKHGLVSOD\
Switching on
Switching off
5HVHW
%DWWHU\FKDQJH
5HPRWHFRQWURO
Remote operating units
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV100 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV100

Siemens REV100 Installation Guide - English, German, Dutch - 4 pages

Siemens REV100 Additional guide - Dutch - 3 pages

Siemens REV100 User Manual - Dutch - 3 pages

Siemens REV100 User Manual - Dutch - 2 pages

Siemens REV100 User Manual - French - 2 pages

Siemens REV100 Installation Guide - French, Italian, Spanish - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info