Manual Siemens REV-R.01-1 (page 10 of 12) (English)

456799

Zoom out

Zoom in

1/12

10/12

Siemens Building Technologies Product-Data Sheet Radio signal unit REV... CE1N2255en

Landis & Staefa Division 16.10.2000

• When mounting the unit, the baseplate must first be fitted and wired (L/N = mains

230 V, LX/L1 = consumers). Then, it must be engaged at the top, swung downward

and secured with a screw

• For more detailed information, please refer to the Installation Instructions supplied

with the unit

For the electrical installation, the local regulations must be complied with.

Commissioning notes receiver REV-R.01/1

It is recommended to first commission and switch on the receiver, then the transmitter.

• Switch on mains supply

a) Press “Reset” button (= delete) for about 4 seconds, LED flashes briefly (delet-

ing the stored address)

b) Press “Set” button (= setting / learning) for about 3 seconds until the LED lights

c) The duration of the receiver’s learning readiness is a maximum of 25 minutes.

If no signal is received from the transmitter during that period of time, repeat

steps b) and c)

d) Mount transmitter and put it into operation

e) When the receiver receives a signal from the transmitter, the LED flashes briefly

f) When the LED is steady on, the relay is energized = controlled device ON

g) When the LED is dark, the relay is de-energized = controlled device OFF

h) In the event of a power failure at the receiver, the relay will automatically be

de-energized.

The transmitter repeats the ON or OFF signal at 20-minute intervals,

depending on the operational status. This means that the relay will be

energized / de-energized again after no more than 20 minutes. This interval

was selected to prolong battery life

If the REV-R.01/1 receives no signal from the controller / transmitter for 60 minutes, the

relay will drop out so that the controlled device will automatically be switched off.

Commissioning notes controller / transmitter REV22RF

It is recommended to first commission and switch on the receiver and then the trans-

mitter.

• If the reference room is equipped with thermostatic radiator valves, they must be fully

opened

• The control mode can be changed with a DIP switch at the rear of the unit

• The battery transit tab, which prevents inadvertent operation of the unit during trans-

port and storage, must be removed from the batteries. The unit switches on

a) When – immediately after switching on – symbol

(controlled device ON)

appears on the display, the first signal has already been transmitted to the

receiver and communication has been opened

b) Make settings in agreement with the Operating Instructions

c) If symbol

(controlled device ON) does not appear on the display, it

must first be activated for signal transmission

d) Set operating mode selector to position

e) Set setting slider to

f) Press - /+ buttons to adjust the setpoint to 29 °C

g) Symbol

(heating ON) appears on the display after a maximum of one

minute

h) The first signal transmission to the receiver has been completed

i) After 10 seconds, the transmitter sends another signal

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV-R.01-1 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV-R.01-1

Siemens REV-R.01-1 User Manual - German - 2 pages

Siemens REV-R.01-1 User Manual - Dutch - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens REV-R.01-1 Manual

Product: