Manual Siemens RDX33 (page 1 of 2) (English)

620393

Zoom out

Zoom in

1/2

CE1B3075en / 31.10.2008 Subject to alteration Building Technologies

Operating Instructions RDX33… / RDX43...

RDX33… / RDX43... – the temperature controller that allows you to set the ideal room temperature you want. The controller provides

protection-,comfort-, energy saving- or auto timer mode with 8 programmable timers.

1.5V

'AA'

1.5V

'AA'

Operation

Warmer / colder

setting the

temperature setpoints

and the time of day

3075Z01en

Display

Button operating mode

Settings

Heating / cooling

changeover button

°C

Temperature

°F

Temperature

1...7

Weekday

Commissioning

Initial

power-up

• Remove the black transit tabs from the 2 alkaline batteries. Check to see if the battery holder is in its correct position. If no

batteries are inserted, fit 2 alkaline batteries type AA in the battery compartment

• Once batteries are fitted, all symbols will appear on the display as shown for about 2 seconds.

Setting the time of day and the weekday

1. Keep the button pressed until the time digits start to flash and then press or to set the time of day. If the current

time is the 24-hour format and you wish to change to the 12-hour format, set P17 to 0 = 12-hour format (or vice versa 1 back

to the 24-hour format).

2. Confirm the time of day by pressing

and the weekday indicator starts to flash.

3. Press

or to set the current weekday.

4. Confirm the current weekday by pressing

Are your rooms too warm or too cold?

Do you want to set your controller to protection?

Press the

button several times until the display shows the symbol

to indicate that protection is selected.

In protection

, the controller maintains the adjusted lower setpoint of heating

(parameter P03) or the higher setpoint of cooling (parameter P04).

Important:

If the setpoint of protection is set to OFF (factory setting), the controller will not be

active.

Risk of frost!

Do you want to change from heating to cooling mode?

The changeover between cooling and heating is done by a remote changeover

switch.

When pressing the

button, the controller changes from heating to cooling or vice

versa.

Do you want to change to auto timer-, comfort or energy saving mode?

Press the

button several times until the display shows the symbols to

indicate which mode you want to select.

The controller will automatically change over comfort mode and energy saving mode

according to the 8 preprogrammed timers.

Do you want to set the programmable timer settings?

A..

To adjust the time schedule, keep the button pressed for 3 seconds to go to

the programmable timer setting mode.

This mode is indicated by displaying Ax (x= auto timer 1...8) and the time xx:xx

flashing. For each auto timer, proceed as follows:

1. The

and symbols are displayed. Press or to adjust the comfort

operation start time and confirm by pressing

2. The

and symbols are displayed. Press or to adjust the comfort

operation end time or energy saving start time respectively and confirm by

pressing

3. Symbol

will flash. Press or to select or deselect each day and

advance to the next day. Confirm setting for actual timer by pressing

and advance to the next timer

The controller will leave the programmable timer setting mode if no button is pressed

within 20 seconds. All changes made after the last press of

button will not be

saved.

Only applicable in comfort operation.

Pressing

or allows you to increase or decrease the current room temperature

setpoint for comfort operation in increments of 0.5 °C. The maximum setting range is

from 5...40 °C, unless it is limited by parameters P05 and P06.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDX33 in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDX33

Siemens RDX33 Installation Guide - All languages - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens RDX33 Manual

Product: