620378
2
Zoom out
Zoom in
Previous page
1/2
Next page
CE1B3072en / 03.03.2013 Subject to alteration Siemens Building Technologies / HVAC Products
Set the first switch on time
1. Set the programming selector to position A1. The setting for the first switch on
time flashes.
2. Turn the setting knob counterclockwise - to decrease the time, or clockwise + to
increase the time.
3. When the required switch on time is displayed, move the programming selector
to any other position to confirm the setting.
Set the first switch off time
1. Set the programming selector to position A2. The setting for the first switch off
time flashes.
2. Turn the setting knob counterclockwise - to decrease the time, or clockwise + to
increase the time.
3. When the required switch off time is displayed, move the programming selector
to any other position to confirm the setting.
Set the second switch on time
1. Set the programming selector to position A3. The setting for the second switch
on time flashes.
2. Turn the setting knob counterclockwise - to decrease the time, or clockwise + to
increase the time.
3. When the required switch on time is displayed, move the programming selector
to any other position to confirm the setting.
Set the second switch off time
1. Set the programming selector to position A4. The setting for the second switch
off time flashes.
2. Turn the setting knob counterclockwise to decrease the time, or clockwise + to
increase the time.
3. When the required switch off time is displayed, move the programming selector
to any other position to confirm the setting.
Set comfort temperature
1. Set the programming selector to position
.
2. The setting for the current comfort temperature flashes.
3. Turn the setting knob counterclockwise - to decrease the temperature setting, or
clockwise to increase the temperature setting.
4. When the required comfort temperature is displayed, move the programming
selector to any other position to confirm the setting.
Set energy saving temperature
1. Set the programming selector to position
2. The setting for the current energy saving temperature flashes.
3. Turn the setting knob counterclockwise - to decrease the temperature setting,
or clockwise + to increase the temperature setting.
3. When the required energy saving temperature is displayed, move the
programming selector to any other position to confirm the setting.
Note: Set the controller to RUN when all programming is completed.
Temporarily change current setpoint
1. The current programmed temperature can be changed temporarily when the
operating mode selector is in the AUTO position and the programming selector
in the RUN position.
2. Turn the setting knob slightly in either direction to display the current programmed
temperature, turn it counterclockwise to decrease the temperature, or clockwise to
increase the temperature .This new temperature is maintained until the next
switching time. The hand symbol is displayed when activated.
Changing
the batteries
1. Get 2 new alkaline batteries type AA, 1.5 V.
2. Within 1 minute: Remove the battery holder, then the batteries, insert the new
batteries and replace the battery holder. The old, set values must be checked!
3. Properly dispose of old batteries per environmental regulations.
Front View Receiver
LED Signal Indicator
LED Relay Indicator
The signal is good when the
LED is solid green.
A solid red LED indicates that
there is no signal.
Orange LED indicates relay is on.
OVERRIDE Button *
* Note: When press OVERRIDE
the RF data will not affect the
output during 15 min. After 15
min, the output and LED will not
change if not RF receive. If
receive RF, the output and LED
will follow the RF data.
Press this button to manually switch on or
off
RESET : Press the LEARN & OVERRIDE
button for 4 seconds to delete all transmitter
addresses.
LEARN Button
Rear View Room Unit
(Transmitter)
Press the button to put into learn mode
TEST Button
Used for testing transmission.
Mounting plate must be
removed to get access
to the back!
Learn Button
Press to learn telegram
Configuration instructions for the Siemens RDJ10RF/SET
The Transmitter RDJ10RF room unit and the receiver RCR10/433 are set to communicate (bonded) with
each other at the factory. If they fail to do so at installation or it is necessary to re bond the units due to
loss of communication please follow the following instructions.
1. For room unit: Set the programming switch to RUN and the selector switch to AUTO.
2. If room unit is wall mounted remove from wall or if on table stand remove grey backing plate
3. For receiver Reset by simultaneously pressing the LEARN & OVERRIDE button for 4 seconds.
4. On Receiver Press and release the LEARN button. This puts the receiver in learn mode.
5. On room unit Press and release the LEARN button on the back.
6. A green solid LED indicates a good signal, a red solid LED indicates no signal.
7. To test transmission, press the TEST button on the transmitter, this switches the relay to ON on
the receiver regardless of temperature. The RF TEST symbol appears on the display (1 s).
8. An orange LED indicates that the relay is on.
Energy saving tips without sacrificing comfort
Do not allow room temperatures to exceed 21 ºC.
NOTE: You can press the OVERRIDE button on the receiver to manually switch ON/OFF for a faulty
room unit or transmission protocol.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RDJ10RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDJ10RF in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDJ10RF

Siemens RDJ10RF User Manual - German - 2 pages

Siemens RDJ10RF User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info