555880
1
Zoom out
Zoom in
Previous page
1/2
Next page
s
Operating Instructions
en
RDG100T
RDG160T
RDG100T / RDG160T the electronic room thermostat that allows you to set the ideal room
temperature you want. The thermostat provides Comfort, Economy and Protection mode and, in
addition, an Auto Timer mode with 8 programmable timers. The fan operates either in Automatic
mode or at the selected speed when using Manual mode. You can either rely on the factory settings
or make adjustments that suit your individual needs.
Main display Operating mode
Room temperature
Heating mode
Room temperature in degrees
Celsius
Electric heater on
Room temperature in degrees
Fahrenheit
Cooling
Button lock active Comfort mode
Alert indicator
Economy mode
Condensation in the room
Auto timer
Temporary timer function
active
Protection mode:
Protection against
frost
Indicator for selecting
mode
Weekday 1 = Monday
7 = Sunday
Operating mode button
Setting time and weekday
Setting the auto timers
Fan mode
Program mode button
Current time of day
Automatic
T Fan mode button
Escape (Cancel)
Manual
Low Medium High
Rotary knob Confirmation (OK)
Changing the room temperature
The room temperature setpoint can be adjusted with the rotary knob when
Comfort mode is active or with
Turn the rotary knob clockwise (+) to increase, or counterclockwise (-) to de
the current room temperature setpoint for Comfort mode
The setting range is from 5...40 °C, unless limited by parameters P09 and P10 (for parameter settings,
see reverse side).
Adjusting the fan speed
Low Medium High
Press the fan mode button until the desired fan mode is reached
In Automatic mode
, the fan speed is automatically selected by the thermostat
depending on the setpoint and the actual room temperature.
When the room temperature reaches the setpoint, the fan stops (fac
tory setting) or
keeps running at low speed (P15).
In Manual mode, the fan operates independently and always runs at the same
speed: Low / medium / high
Note:
If desired, you can change the fan mode selector option via P03: Manually only, or manually
including Protection mode. Use P15 to set the fan speed in dead zone.
Changing from heating to cooling mode
Depending on the type of plant, the changeover from heating to cooling (or vice
versa) is made either automatically by a changeover sen
sor or a remote changeover
switch, or manually by pressing the operating mode button (see parameter P01)
To select cooling or heating manually (P01=2), press the operating mode button
until the desired mode appears
With automatic changeover or continuous heating / cooling, symbols
/
indicate that the system currently operates in heating or cooling mode
With manual changeover, symbol
appears, indicating that the system currently
operates in heating or cooling mode
Changing the operating mode
Press the operating mode button until symbol
appears, indicating that Protection /
Comfort / Auto Timer / Economy mode is selected.
1. Protection mode
In protection mode, the plant stops operating. If the room temperature falls below
8 °C, heating is switched on however to protect the room against frost
The setpoints for Protection mode can be changed by your HVAC installer if desired:
Changes made by installer: Frost protection: _________ C Heat protection: __________C
2. Comfort mode
In Comfort mode, the thermostat maintains the setpoint which can be readjusted
with the rotary knob
3. Auto Timer mode
In Auto Timer mode
, the controller automatically switches over between Comfort
and Economy according to the 8 preprogrammed timers
4. Economy mode
When selecting Economy mode, make sure that parameter P02 is set to 2
In Economy mode, the room temperature is maintaine
d at a lower or higher
setpoint, thus saving energy and money! You can change the preselected
setpoint
by adjusting parameters P11 and P12 (for parameter settings, see reverse side)
Important: The setpoint for Economy can be set to OFF. This means that the thermostat is
deactivated! Risk of frost, i.e. no protective heating or cooling function is provided!
Setting the time of day and the weekday
1. Press the program mode button for programming.
2. Press button (OK) to enter the setting mode for the time of day.
3.
The time digits start blinking. Turn the rotary knob clockwise or counterclockwise to set the time
of day.
If the current time of day is in 24-hour format and you wish to change it to the 12-hour format, turn
the knob clockwise passed 23:59 or counterclockwise passed 00:00. Vice versa back to the 24-hour
format.
4. Confirm the time of day by pressing button and the weekday indicator starts blinking.
5. Turn the rotary knob clockwise or counterclockwise to set the current weekday.
6. Confirm the current weekday by pressing button (OK).
7. Press button (Esc) to leave the program mode.
Note:
After a power failure, the time of day starts blinking to indicate power was lost. However, the auto timer continues to
run with the time before the power failure occurred. Select the setting mode to readjust the time if needed.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RDG160T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDG160T in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDG160T

Siemens RDG160T User Manual - German - 2 pages

Siemens RDG160T User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info